Creator 3

3D Print Removal Tool - Scraper Includes: Scraper (1 pcs)

  Flashforge 3D Print Removal Tool Spatula for removing 3D prints from the build surface. This is the same tool that is provided with many of the new Flashforge 3D printers.  Includes: Spatula (1 pcs)

Flashforge Hotend Air Duct (Left Side) Directs air to the part being printed Includes: Left side air duct (1pcs) Fits: Creator 3 Note: Does not include mounting screws

  Flashforge Hotend Air Duct (Right Side) Directs air to the part being printed Includes: Right side air duct (1pcs) Fits: Creator 3 Note: Does not include mounting screws

  Flashforge Air Filter HEPA and charcoal air filter. Includes: Filter (1 pc) Fits:Adventurer 4Robo E4 ProGuider 3Guider 3 PlusCreator 3Creator 3 Pro

  Flashforge Bed Leveling Card Includes: Leveling card (1 pcs)

  Flashforge Bed Leveling Hardware  For leveling the build plate.  Includes:Spring (3 pcs)Thumb Nut (3 pcs) Fits: Creator 3Creator 3 ProGuider 2Guider 2S HTRobo E3 Pro

  Flashforge Bed Leveling Springs - 3 Pack Strong springs for leveling the build plate.  Includes: Spring (3 pcs) Fits: Creator 3Creator 3 ProGuider 2Guider 2S HTRobo E3 Pro

Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotend. Contains high quality ZYP™ Boron Nitride and proprietary binders which reduce cracking and flaking when dried...

   !! WARNING !!  This is a very delicate part. When handling and installing do not press or put any pressure on the middle eyelet (see picture), this eyelet will break with even a small amount of pressure.  Bottom Housing for...

  Linear Rod and Pulley Bracket Holds Y axis rod and pulley in place. Includes: Bracket (1 pcs) Location: Front left or right corner. Fits: Creator 3 Note: Mounting hardware not included.

  Linear Rod and Pulley Bracket Holds Y axis rod and pulley in place. Includes: Bracket (1 pcs) Location: Left Rear corner only Fits: Creator 3 Note:Mounting hardware not included.The Location is the Left Rear when you are standing...

Brim Scraper (Mini Scraper) We find this tool handy for removing the brim, and purge lines from the build plate. Includes: Brim Scraper (1 pcs)

  Flashforge Magnetic Build Plate Base For use with Flashforge flexible build plate (not included) Includes: Magnetic build plate base (1 pcs) Fits: Creator 3

  Flashforge Build Plate Heater Includes: Heater with wire & connector (1 pcs) Fits: Creator 3

  Flashforge Bed Leveling Sensor Switch Includes:Sensor switch (1 pcs)Plastic housing (1 pcs) Fits: Creator 3 (with 3 wire switch) Note: Important! This is for the later version Creator 3 which has the 3 wire switch. If your current switch has...

  Flashforge Filament Sensor Cable - Left Runs from left side filament sensor to mainboard. Includes: Cable (1 pcs) Fits: Creator 3 (Left Side)

  Flashforge Filament Sensor Cable - Right Runs from the right side filament sensor to the mainboard.  Includes: Cable (1 pcs) Fits: Creator 3 (Right Side)

  Flat Cable for TFT Touch Screen Connects touch screen to mainboard Includes: Cable (1 pcs) Fits: Creator 3  WARNING  Pay attention to the orientation of your current cable.Plugging this cable in backwards will...

  Flashforge X Motor Cable (Left Side) This cable runs from the mainboard to the X axis stepper motor that moves the left extruder Includes: Cable (1 pcs) Fits: Creator 3Creator 3 Pro