Creator 4

  6063 GT Pulley Includes: 6063 2GT Pulley (1 pcs) Fits: Creator 4 Note: 2 set screws needed for installation (not included). Set screws available here.

3D Print Removal Tool - Scraper Includes: Scraper (1 pcs)

  Flashforge 3D Print Removal Tool Spatula for removing 3D prints from the build surface. This is the same tool that is provided with many of the new Flashforge 3D printers.  Includes: Spatula (1 pcs)

  X Axis Belt Includes: Belt (1 pcs) Location: X axis Fits: Creator 4

  Y Axis Belt Includes: Belt (1 pcs) Location: Y axis Fits: Creator 4

  Z Axis Belt Includes: Belt (1 pcs) Location: Z axis Fits: Creator 4

  Flashforge Print Cooling Fan This fan cools the part being printed Includes: Fan (1 pcs) Fits: Creator 4

  Flashforge Blower (Turbo) Fan This fan cools the part being printed Includes: Fan (1 pcs) Fits:Guider 3 UltraCreator 4

Brim Scraper (Mini Scraper) We find this tool handy for removing the brim, and purge lines from the build plate. Includes: Brim Scraper (1 pcs)

  Flashforge Bed Leveling Sensor Switch Includes: Sensor (1 pcs)Sensor bracket (1 pcs) Fits: Creator 4

  Cable for Touch Screen Includes: Cable (1 pcs) Fits: Creator 4

  Chamber Fan (120x120x25mm) This is the chamber fan that is located behind the HEPA filters. Includes: Fan (1 pcs) Fits: Creator 4Guider 3 PlusGuider 3 Ultra

  Door Sensor Switch Includes: Door sensor (1 pcs) Fits: Creator 4

  Flashforge E-Clips For holding timing pulley to 5mm motor and axle shafts Includes: E-Clip (5pcs)

3D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

  Flashforge Extruder Adapter Board Includes: Adapter board (1 pcs) Fits: Creator 4

  Flashforge Main Cable (LEFT) This cable is about 6 feet long and runs from mainboard to the extruder transfer board. Includes: Cable (1 pcs) Fits: Creator 4

  Flashforge Main Cable (RIGHT) This cable is about 6 feet long and runs from mainboard to the extruder transfer board. Includes: Cable (1 pcs) Fits: Creator 4

  Flashforge Extruder PCB Board - Left Side Includes: PCB Board (1 pcs) Fits: Creator 4 Note: For left side extruder only

  Flashforge Extruder PCB Board - Right Side Includes: PCB Board (1 pcs) Fits: Creator 4 Note: For right side extruder only

  Flashforge Extruder Wire Harness Runs from extruder to adapter board. Includes: Wire harness (2 pcs)Bracket (2 pcs) Fits: Creator 4

  Flashforge Extruder Cooling Fan This fan cools the heatsink Includes: Fan (1 pcs) Fits: Creator 4

  Flashforge Filament Drive (Extruder) Gear Includes: Gear (1 pcs)Set screw (1 pcs) Fits: Creator 4

  Flashforge Filament Sensor Switch Includes: Sensor (1 pcs) Fits: Creator 4 Note: Not for F extruder

Small Phillips Head Screwdriver This is the small screwdriver that comes with the accessory kit of many new Flashforge 3D printers Includes: Screwdriver (1 pcs)

  Flexible Build Plate with Powder-coated Textured PEI Print Surface Includes: Flexible steel sheet (1 pcs)pcs) Fits: Creator 4ACreator 4FCreator 4S

  Flashforge Flexible Build Plate Includes:Flexible steel sheet (1 pcs)Print surface - installed (1 pcs) Fits:Creator 4ACreator 4S

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

Flashforge 3D Printer Grease This is the same grease that comes standard with many Flashforge 3D Printers. Size: 3 Grams Includes: Grease packet (1 pcs)

Flashforge Hardened Steel Nozzle Hardened steel nozzles for printing with abrasive materials  Includes: Nozzle of selected size (1 pcs) Material: Hardened Steel Fits:Guider 3Guider 3 PlusCreator 3 Pro (does not fit standard Creator...

  Flashforge Hardened Steel Nozzle Set This upgraded nozzle set is more abrasion resistant for printing carbon fiber filled and other abrasive filaments. Includes:0.40mm (2 pcs)0.60mm (2 pcs)0.80mm (2 pcs) Fits: Guider 3Guider 3 PlusCreator...

  Flashforge Heat Break (Threaded Pipe) *Note: This heat break is only compatible with the older version hotend. Please check the picture and make sure it matches the part you are replacing. It will not work with the new (V2) version hotend...

  Flashforge V2 Heat Break (Threaded Pipe) *Note: This heat break is only compatible with the new version hotend. Please check the picture and make sure it matches the part you are replacing. It will not work with the older (V1) version...

  Heater Block for Left Side Hotend Includes: Heater block (1 pcs) Location: Left Side Fits: Creator 4

  Heater Block for Right Side Hotend Includes: Heater block (1 pcs) Location: Right Side Fits: Creator 4

  Flashforge Heater Cartridge Includes: Heater cartridge (1 pcs) Fits: Creator 4

  V2 Hotend Heatsink Includes: Heatsink V2 (1 pcs) Fits: Creator 4 Note: Only fits the V2 hotend. Check the picture and make sure it matches your current heatsink before ordering.  

  Flashforge HEPA Filter Includes: HEPA filter (1 pcs) Size: 120x120x15mm Fits: Creator 4

  Left Side Hotend Assembly with 0.40mm Hardened Steel Nozzle Includes: Heat break (1 pcs)Heater block (1 pcs)Temperature sensor (1 pcs)Heater (1 pcs)Nozzle -  0.40mm  hardened steel (1...

  Right Side Hotend Assembly with 0.40mm Hardened Steel Nozzle Includes: Heat break (1 pcs)Heater block (1 pcs)Temperature sensor (1 pcs)Heater (1 pcs)Nozzle -  0.40mm  hardened steel (1 pcs) Location: Right...

  Left Side HT Hotend Assembly with 0.40mm Nozzle Includes: Heat break (1 pcs)Heater block (1 pcs)Temperature sensor (1 pcs)Heater (1 pcs)Nozzle -  0.40mm  (1 pcs) Location: Left Side Fits: Creator 4 *Notes: Does...

  Right Side HT Hotend Assembly with 0.40mm Nozzle Includes: Heat break (1 pcs)Heater block (1 pcs)Temperature sensor (1 pcs)Heater (1 pcs)Nozzle -  0.40mm  (1 pcs) Location: Right Side Fits: Creator 4 *Notes: Does...

  Left Side V2 Hotend Assembly with Hardened Steel 0.60mm Nozzle Replacement hotend for the Creator 4 V2 Extruder. Includes: Heatsink (1 pcs)Heat break (1 pcs)Heater block (1 pcs)Heater (1 pcs)Temperature sensor (1 pcs)Nozzle...

  Right Side V2 Hotend Assembly with Hardened Steel 0.60mm Nozzle Replacement hotend for the Creator 4 V2 Extruder. Includes: Heatsink (1 pcs)Heat break (1 pcs)Heater block (1 pcs)Heater (1 pcs)Temperature sensor (1 pcs)Nozzle -  0...

  Left Side High Temperature Hotend Assembly with 0.60mm Nozzle Includes: Heat break (1 pcs)Heater block (1 pcs)Temperature sensor (1 pcs)Heater (1 pcs)Nozzle -  0.60mm  (1 pcs) Location: Left Side Fits: Creator...

  Right Side HT Hotend Assembly with 0.60mm Nozzle Includes: Heat break (1 pcs)Heater block (1 pcs)Temperature sensor (1 pcs)Heater (1 pcs)Nozzle -  0.60mm  (1 pcs) Location: Right Side Fits: Creator 4 *Notes: Does...

  Flashforge LED Board - Light Strip Includes: LED light board (1 pcs) Fits:Guider 3Guider 3 PlusGuider 3 UltraRobo E4 Pro Creator 4

  Flashforge Limit Switch (Endstop) Includes: Limit switch (1 pcs) Fits:Guider 3 (Y/Z)Guider 3 Plus (Y/Z)Creator 4 (X/Y)Robo E4 Pro (Y/Z)

  Please read our returns policy regarding electronic items Flashforge Creator 4 Mainboard This board is also known as the motherboard or control board. Fits: Creator 4

  Microswiss Wear Resistant Nozzle (Plated Brass) Made from a 360 brass base material and plated with TwinClad XT coating.TwinClad XT coating is a nickel composite designed for very low friction. It offers one of the lowest coefficient of...

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

  Flashforge Stainless Steel Nozzle Set Includes:0.40mm (2 pcs)0.60mm (2 pcs)0.80mm (2 pcs) Fits: Guider 3Guider 3 PlusCreator 3 Pro (does not fit standard Creator 3)Creator 4Robo E4 Pro 

  Flashforge Replacement Power Supply Includes: Power supply unit (1 pcs)  Fits: Creator 4

  PTC Chamber Heater Includes: Heater (1 pcs) Fits: Creator 4

  Radial Fan (30x150mm) Includes: Fan (1 pcs) Fits: Creator 4

Stainless Steel Nozzle Includes: Nozzle of selected size (1 pcs) Material: Stainless Steel Fits:Guider 3Guider 3 PlusCreator 3 Pro (does not fit standard Creator 3)Creator 4Robo E4 Pro

  Stepper Motor for X Axis Includes: X Axis Stepper Motor (1 pcs) Fits: Creator 4

  Stepper Motor for Z Axis Includes: Z Axis Stepper Motor (1 pcs)Pulley (1 pcs) Fits: Creator 4

  Hotend Support Pins These pins go between the heater block and heatsink on the V1 extruder.  Includes: Pin (6 pcs) Fits: Creator 4

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

  Flashforge Thermocouple  Includes: Thermocouple (1 pcs) Fits:Creator 3Creator 3 ProCreator 4

Tube Grease for lubing the rods and ball screws of your 3D printer. This is the same grease that comes stock with Robo 3D R1+/R2 printers. Includes: Grease (1 pcs) Size: 10g

  Hotend Unclog Pin Helps clear blockages from the hotend Diameter: 1.5mmLength: 133mm Includes: Unclog pin (1 pcs)