Creator Pro 2

Socket Head Cap Screw - 4 pack Size: M3x16 Includes: M3x16 socket head cap screw (4 pcs) Used in the following locations on the printers listed below:Extruder to carriageFan to heatsinkStepper motor mounting. Fits:Creator Pro 2Creator Max 2

Replacement Magnet sheet for 154*232mm DFlex™ Build Plate Includes: Sheet magnet with adhesive backing (1 pcs) Size: 154*232mmMax temperature: 90c Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2InventorDreamerDreamer NX

  Please read our returns policy regarding electronic items Note: This is a new board that was removed from a brand new Creator Pro 2  Flashforge Creator Pro 2 Mainboard This board is also known as the motherboard or control board...

Microswiss Plated Wear Resistant Nozzle This nozzle is made from a 360 brass base material and plated with TwinClad XT coating. TwinClad XT is a nickel composite coating designed for very low friction. It offers one of the lowest coefficient of...

  Timing Belt (Motor) Drive Pulley This is the drive pulley that is used on many Flashforge 3D printers. Includes:Pulley (1pcs)Pulley disc (1 pcs)E-clip (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Creator ProCreator Pro...

  Flashforge Motor Mount Includes: Motor mount (1 pcs) Location: Y Axis Motor Fits:FinderFinder 2Inventor 2Creator ProCreator Pro 2Creator MaxCreator Max 2

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

  Flashforge Brass Nozzle Size: (Select Above) Includes:Brass nozzle (1 pcs)PTFE tube (1 pcs) Fits:Creator Pro 2Creator Max 2

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

  Flashforge Ooze Plate Fits: Creator Pro 2Creator Max 2 Note: Mounting hardware not included

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

  Flashforge Power Inlet & On/Off Switch Includes:Power inlet with switch (1 pcs)Fuse (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Guider 2SRobo E3 Pro

   Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Flashforge Power Inlet & On/Off Switch Includes:Power inlet with switch (1 pcs)Fuse (1 pcs) Fits:Creator ProCreator...

  Flashforge Replacement Power Supply Includes: Power supply unit (1 pcs)  Fits:Creator ProCreator Pro 2Creator Max Creator Max 2DreamerDreamer NXInventor

  Flashforge Print Surface Bed Tape Adhesive backed for easy application Includes: Print surface (1 pcs) Size: 153x232mm (can be cut to fit other printers) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Inventor (for Inventor 2 bed tape...

  Flashforge PTFE Tube for Nozzle This is the PTFE tube that goes inside the nozzle. Includes: PTFE tube (1 pcs) Fits:Creator Pro 2Creator Max 2

   Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Pulley Bracket Front Kit Holds Y axis rod in place Includes:Bracket (2 pcs)Idler Pulley Assembly (2 pcs) Location:Left...

  Flashforge Idler Pulley Assembly Includes: Idler pulley assembly (1 pcs) For: X-Axis Fits: Creator Pro 2Creator Max 2

   Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Flashforge Idler Pulley Assembly Includes: Idler pulley assembly (1 pcs) For: X-Axis Fits: Creator Pro 2Creator Max...

  Flashforge Idler (Driven) Pulley Assembly Center shaft is about 37mm long Includes: Pulley assembly (1 pcs) Location: Y-Axis Fits:Creator ProCreator Pro 2Creator Max 2