M3
Use the filter box below to narrow down the MakerGear M3 parts you are looking for:
-
3D Print Removal Tool - Red Handle Scraper
PB Select™
$4.993D Print Removal Tool - Scraper Includes: Scraper (1 pcs)$4.99 -
40x10mm 24v Extruder Fan - M2*, M3 | MakerGear
MakerGear OEM
$15.004010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against incorrect plug-in. All fans should be kept free of...$15.00 -
40x15mm 24v M3 Bed Fan | MakerGear
MakerGear OEM
$15.004015 Bed Fan This is the fan the cools the part being printed. It is sometimes called the print or part cooling fan. Includes: Fan (1 pcs) Voltage: 24 VDCSize: 40x40x15mm Fits: M3$15.00 -
Aluminum Motor Mount for M3 | MakerGear
MakerGear OEM
$29.95Aluminum Motor Mount This is the extruder motor mount that comes standard on the M3-ID and M3-SE Rev.1 machines Includes: Motor mount (1 pcs)M3x22 bolts (3 pcs) Fits:M3-SEM3-ID$29.95 -
Bed Heater (24 volt) M2, M3 | MakerGear
MakerGear OEM
$32.95Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available separately here$32.95 -
Bed Thermistor | MakerGear
MakerGear OEM
$25.00MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3$25.00 -
Boron Nitride Thermal Paste
PB Select™
Regular Price: $11.65 - $116.50$4.99 - $49.95Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotend. Contains high quality ZYP™ Boron Nitride and proprietary binders which reduce cracking and flaking when dried...Regular Price: $11.65 - $116.50$4.99 - $49.95 -
Brim Scraper (Mini Scraper) Black or Orange
PB Select™
$1.99Brim Scraper (Mini Scraper) We find this tool handy for removing the brim, and purge lines from the build plate. Includes: Brim Scraper (1 pcs)$1.99 -
Edge Cleanup (Deburring) Tool for 3D Prints
NOGA
$13.953D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...$13.95 -
Extruder Motor - Base | MakerGear
MakerGear OEM
$24.95Extruder Stepper Motor for MakerGear 3D printers Includes:1.8° stepper motor basePinion gear (installed) Fits:M2M3 Note: Does not include the 5.16:1 planetary gearbox.$24.95 -
Fiberglass Insulation (for V4 Hotend) M2, M3 | MakerGear
MakerGear OEM
$2.99Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries- Expandable and rubber-coated- Suitable for both the V4...$2.99 -
Filament Drive Gear - M2, M3 | MakerGear
MakerGear OEM
$19.99MakerGear Filament Drive Gear Replacement This gear drives the filament through the extruder. Fits: M2M3-SEM3-ID$19.99 -
Filament Guide Tube for MakerGear M2, M3
PB Select™
$9.95PB Select™ Filament Guide Tube for MakerGear Includes: Guide tube (1 pcs) Fits:M2M3$9.95 -
Flush Cut Trimmer (Side Cutters)
PB Select™
$4.99Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints. Includes: Trimmers (1 pc)$4.99 -
Glass Build Surface - 8x10in (203x254mm) M2, M3 | MakerGear
MakerGear OEM
$26.958x10 Build Surface for MakerGear Printers Made from borosilicate glass, this 8"x10"x0.13" (20cm x 25 cm x 3.3 mm) comes standard with a sheet of polyimide tape already applied. Includes: Glass print surface (1 pcs)Polyimide tape (1...$26.95 -
GT Pulley - 20T - 5mm Bore (for 6mm GT Belt)
PB Select™
$3.99PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm$3.99 -
Heat Break for Copperhead Hotend - MK10 | Slice Engineering
Slice Engineering
$29.95Slice Engineering Copperhead™ Heat Break for MK10 Bimetallic Heat Break™ - Stainless steel and Copper AlloyRated to 450 °C For more documentation on the Copperhead™ Heat Break, please see the Technical Specifications...$29.95 -
Heatsink for Nema17 Stepper Motor - Black
PB Select™
$2.49PB Select™ Black Heatsink for Nema17 Stepper Motor Heatsink in black anodized aluminum to remove heat from desired component.Equipped with self-adhesive on the back for easy attachment. Includes: Heatsink (1 pcs) Size: 40x40x10 mm$2.49 -
Idler Pulley Set - M2 (Rev G-H), M3 | MakerGear
MakerGear OEM
$24.95Idler Pulley Set for MakerGear 3D Printers Includes:Bolt (1 pcs)Toothed Pulley (1 pcs)Nylon Bushing (1 pcs) Note: You need one pulley for each belt. Order 2 sets if you need a pulley for each belt. Fits:M3-SEM3-IDM2 Rev G-H$24.95 -
Limit Switch (X Axis) M3 | MakerGear
MakerGear OEM
$2.99MakerGear X Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M3$2.99