Printer Parts

Artillery 10A Fuse Fuse for the power on/off switch. Includes: Fuse (1 pcs) Fits: GeniusSidewinder X1

Replacement Fuse 5 amp fuse

  Flashforge 8a Fuse Includes: Fuse (2 pcs) Location: Power inlet plug (on/off switch) Fits: Adventurer 3 (all versions)Monoprice VoxelRobo E3

Fuse Pack Replacement fuses for Einsy and RAMBo boards Includes:15 amp blade fuse (1 pcs)5 amp blade fuse (2 pcs) Fits:Prusa Einsy for MK3/S/+Prusa RAMBo Mini for MK2/S & MK2.5/SUltiMachine EinsyUltiMachine RAMBo Mini

  Flashforge FFC Flat Cable for Bed Gauge Sensor Runs from heated build plate to strain gauge sensor board. Includes: FFC Cable (1 pcs) Fits:Adventurer 5MAdventurer 5M ProRobo E4 Note: This is narrow cable that plugs into the bed, not...

Glass Bed and Heater Kit Comes fully assembled. Includes: Glass build plate (1 pcs)Heater (1 pcs)Insulation pad (1 pcs) Fits: Hornet

  Flashforge Finder 3 Glass Print Surface (Build Plate) Includes: Glass print surface (1 pcs) Fits: Finder 3

  Flashforge Glass Build Plate Includes: Glass build plate (1 pcs) Fits: Adventurer 3 Note: This is not an upgrade kit, this bed will only work if your printer already uses a glass build plate.  WARNING  Always allow the...

  Flashforge Glass Build Plate One side is smooth, one side is textured. Includes: Glass build plate (1 pcs) Fits:Adventurer 4 LiteAdventurer 4 (with glass build plate) Notes:This is not an upgrade kit. If your printer currently has a magnetic...

Artillery Glass Build Plate (Print Bed) Includes:Carborundum glass bed (1 pcs)Mounting bolts - preinstalled (4 pcs) Fits:Sidewinder X1Sidewinder X2  WARNING  Allow the bed to cool completely before attempting to remove a print...

  Flashforge Glass Build Plate Assembly You can use this assembly to convert your Adventurer 3 to a glass build plate. Includes: Glass build plate (1 pcs)Build plate frame (1 pcs)Heater (1 pcs)Heater pads (4 pcs)Mounting screws (3 pcs)Bearing...

Glass Build Plate (Print Bed) Carborundum glass build platform with mounting bolts Includes: Glass bed with attached mounting bolts (1 pcs) Fits:GeniusGenius Pro  WARNING  Allow the bed to cool completely before attempting to...

  8x10 Build Surface for MakerGear Printers Made from borosilicate glass, this 8"x10"x0.13" (20cm x 25 cm x 3.3 mm) comes standard with a sheet of polyimide tape already applied. Includes: Glass print surface (1 pcs)Polyimide tape (1...

Stepper Splitter Board The GPIO module (General Purpose Input/Output) is an optional add-on PCB that can be connected to the Original Prusa MK4/S, MK3.9/S, or MK3.5/S. It extends functionality by allowing you to control and receive input from external...

Flashforge 3D Printer Grease This is the same grease that comes standard with many Flashforge 3D Printers. Size: 3 Grams Includes: Grease packet (1 pcs)

2GT Timing Belt for Prusa i3 Series Y axis Includes: Timing belt for Y axis (1 pcs) Specifications:Type: 2GTLength: 650 mmWidth: 6 mmPitch: 2 mm Location: Y Axis Fits:MK2MK2SMK2.5MK2.5SMK3MK3SMK3S+MK3.5MK3.5SMK4MK4S To replace this part, please...

2GT Timing Belt for Prusa i3 Series X Axis Includes: Timing belt (1 pcs) Specifications:Type: 2GTLength: 850 mmWidth: 6 mmPitch: 2 mm Location: X Axis Fits:MK2MK2SMK2.5MK2.5SMK3MK3SMK3S+MK3.5MK3.5SMK4MK4S To replace this part, please visit the Prusa...

Prusa X Axis GT Timing Belt Includes: Belt (1 pcs) Location: X axis Fits:MINIMINI+ To replace this part, please visit the Prusa knowledge base at help.prusa3d.com

Robo C2 Belt This is the short belt that runs from the stepper motor to the X/Y axis shaft. Includes: Belt (1 pcs) Length: 260mm Fits: Robo C2

Prusa Y Axis Timing Belt Includes: Belt - Y Axis (1 pcs) Fits:MINIMINI+ To replace this part, please visit the Prusa knowledge base at help.prusa3d.com