Printer Parts

  Idler Set for MakerGear M2 3D Printers Includes:Bolt (1 pcs)Bearings (3 pcs)E-clip (1 pcs) Fits: M2 Rev A through F Note: for the MakerGear M2 Rev G through H, use the M3 idler set available here

Prusa Pulley With Bearing Includes: Pulley with bearing (1 pcs) Fits: XL To replace this part, please visit the Prusa knowledge base at help.prusa3d.com

PB Select™ Idler Pulley Includes: Idler pulley (1 pcs) Fits:MK2MK2SMK2.5MK2.5SMK3MK3SMK3S+MINIMINI+ To replace this part, please visit the Prusa knowledge base at help.prusa3d.com

Artillery Idler Shaft Sleeve Includes: Sleeve (1 pcs)  Fits: Sidewinder X1Sidewinder X2GeniusGenius ProHornet

  iFixit Mako Driver Kit Driver kit from iFixit. The Mako set includes nearly all the necessary bits you'll need for repairs or assembly on any Original Prusa 3D Printer, use the Mako set to build your 3D printer kit. Perform basic maintenance,...

  Flashforge IFS Cable Connects IFS module to printer. Includes: IFS cable (1 pcs) Fits: AD5X

Bondtech IFS Extruder for Prusa MINI/+ (IDGA) Latest version with white plastic main gear and integrated drive gear for lower run-out (IDGA) Bondtech extruder upgrade for the Prusa MINI/+. This version allows you to install the Prusa filament...

  Motor for IFS Filament Feeding This is the motor the feeds the filament from the IFS system to the extruder. Includes: Motor (1 pcs) Fits: AD5X

  Flashforge IFS Module Includes: IFS Module (1 pcs)Signal cable (1 pcs)Mounting plate (1 pcs)PTFE tube (4 pcs)4-into-1 connector (1 pcs) Fits: AD5X

  Flashforge IFS Mounting Bracket This is the plate for mounting the IFS module to the printer. Includes: IFS mounting plate (1 pcs)Mounting screws (2 pcs) Fits: Flashforge AD5X

  Flashforge IFS Single Filament Channel Includes: Single Channel (1 pcs) Fits: AD5X

CNC Kitchen Installation Tips for Heat Set Inserts Compatible with soldering irons that use T18 and M900 standard like Hakko, Lonovo, Sremtch. Includes:Tip - M2/M2.5 (1 pcs)Tip - M3 (1 pcs)Tip - M4 (1 pcs)Tip...

CNCKitchen Installation Tips Set for Short and Standard Threaded Inserts. Tips for easy installation of both short and standard threaded inserts. Includes:Tips for TS100 adapter (6 pcs)TS100 adapter (1 pcs) Specifications:Compatible with TS100,...

  4010 Air Filter Fan This fan is used for the internal air filter. Includes: Fan (1 pcs) Size: 40x40x10mm Fits:Adventurer 5MAdventurer 5M ProRobo E4

Prusa IR Filament Sensor Includes: IR filament sensor (1 pcs)  Fits:MK2.5SMK3SMK3S+ Notes:This IR filament sensor is ONLY compatible with the MK2.5S, MK3S and MK3S+. It is not compatible with the MK2.5 and MK3.The IR...

PB Select™ IR Filament Sensor This is a Prusa compatible version, if you want a genuine Prusa filament sensor check here. Includes: IR filament sensor (1 pcs)  Fits:MK2.5SMK3SMK3S+ Notes:This IR filament sensor is ONLY compatible...

Cover for IR Bed Leveling Sensor Includes: Cover (1 pcs) Fits:Robo R2Robo C2

2.54 Jumper Includes: Jumper (24 pcs)

PB Select™ Kapton & Aluminum Tape Used to attach the thermistor to the heated bed on Prusa and other 3D printers. Includes:Kapton Tape - adhesive backed, approximately 4x4 inches (1 pcs)Aluminum Tape...

*Clearance item - no returns  Blemished  These rolls of tape are wound slightly off-center, however the tape is good and fully usable.  Heat Resistant Kapton Tape Use this tape to secure the insulation to your Flashforge heater...