Supplies

  Basics of 3D Printing with Josef Prusa   English Version  "Basics of 3D Printing" takes you on a tour through the 3D printing world. This is a print version, the e-book can be downloaded for free at prusa3d...

  Basics of 3D Printing with Josef Prusa   Spanish Version  "Basics of 3D Printing" takes you on a tour through the 3D printing world. This is a print version, the e-book can be downloaded for free at prusa3d.com...

Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotend. Contains high quality ZYP™ Boron Nitride and proprietary binders which reduce cracking and flaking when dried...

HARDMAN DOUBLE/BUBBLE 2 Part Epoxy - Very High Peel Strength - Orange This is the epoxy we use for attaching the magnets to the R1/+ glass print bed. Full curing time is stated to be 7 days. However, when applying magnets to the R1 glass bed, we...

Henkel 60905 LOCTITE® 609™ Press Fit Retaining Compound - .5 mL (.02 oz) Capsule This is what MakerGear recommends for installing the pinion gear onto the extruder motor shaft of the M2/M3 3D Printers MSDS

M3 Leaf Spring T-Slot Nut (3030) Plated roll-in t-slot nut with leaf spring. Includes: M3 T-Slot nut with leaf spring (5 pcs) Size:(Measured by hand - sizes are approximate)Length: 19.5mmWidth: 12mmHeight: 6.5mm Fits:3030 extrusionPrusa...

  Spool Holder Includes: Spool holder (1 pcs) Color: Black Holds up to 5gk spoolsBearings for smooth feedingNone slip feetAssembly required

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

Poly Prep Refill for Tech-Bond Polymer Bonding Kit Includes: 1.5 ounce bottle of Poly Prep (1 pcs)  

Tech-Bond Basic Poly Kit This is the best bonding system we have found for bonding 3D printed parts. It bonds everything, even Nylon and PTFE. We keep this around our shop and use it whenever we need to glue printed parts together. Kit Contains One...

M3x4 Set Screw (Grub Screw) Includes: Set screw (5 pcs) Size: M3x4mmGrade: 12.9Head Type: Hex Fits heater block of:E3D V6Prusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4SPrusa XL Note: These are hex head set screws, not torx head (torx head is...

M3X4 Torx Head Set Screw Used on the Nextruder heater block Includes: M3x4 set screw (5 pcs) Note: Uses T6 Torx driver to install (not included) Fits:Prusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4SPrusa XL

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

GD900 Thermal Grease Size: 1 gram Max working temp: 200c This thermal grease can be used on the cold-end side of the heat break to help dissipate heat to the heatsink. Do not use on the hotend side. For the hotend side, including the heater and...

Vibra-Tite Blue Threadlocker  This is a good medium strength thread locker for securing 6mm (or larger) fasteners. For smaller fasteners use purple threadlocker. Includes: 1.8ml Threadlocker (1 pcs) Note: Not intended for use in the hotend...

Vibra-Tite Purple Threadlocker This is a good low strength thread locker for securing small screws on your 3D printer. Includes: 1.8ml threadlocker (1 pcs) Note: Not intended for use in the hotend  Strength: LowColor: PurpleSize: 1.8...