MakerGear OEM

Aluminum Motor Mount This is the extruder motor mount that comes standard on the M3-ID and M3-SE Rev.1 machines Includes: Motor mount (1 pcs)M3x22 bolts (3 pcs) Fits:M3-SEM3-ID

  MakerGear X Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M3

MakerGear Z Axis Limit Switch Includes: Limit switch (1 pcs) Fits:M2M3

  MakerGear Y Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M3

MakerGear X Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M2

  SD Card Reader Includes: Card reader (1 pcs) Fits: MakerGear M2

MakerGear Z Stepper Motor with Leadscrew and Nut Includes: Z motor with integrated leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits:M3 SEM3 IDM2 RevG or later (with black z motor) Note: The...

  Bed Spring - M2 older version bed - 3 Pack Includes: Spring (3 pcs) Fits: MakerGear M2 (that have a 3 point bed with springs).

  Heater Block for MakerGear V4 Hotend Includes:Heater Block (1 pcs)Set Screws (2 pcs) Fits:M2 (with V4 hotend)M3-SEM3-ID

  Extruder Stepper Motor for MakerGear 3D printers Includes:1.8° stepper motor basePinion gear (installed) Fits:M2M3 Note: Does not include the 5.16:1 planetary gearbox.

  5010 Extruder Fan for MakerGear M2 Dual Extruder - 24 volt  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 Dual Extruder  This...

  Pinion Gear for MakerGear 3D Printers Goes on the extruder stepper motor shaft inside the gearbox. Fits:M2M3 SEM3 ID Use Loctite 609 to attach to motor shaft. Buy Loctite 609 here

MakerGear Filament Drive Gear Replacement This gear drives the filament through the extruder. Fits: M2M3-SEM3-ID

  4010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 40x40x10mmLocation: Extruder or electronics case Fits: M2 (12 volt...

  5010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (12 volt version) Mounted at a 45...

  5010 Extruder Fan for MakerGear M2 - 24 volt Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (24 volt version) Mounted at a 45 degree...

V4 Hotend Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1...

V4 Hot End Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1...

  Idler Pulley Set for MakerGear 3D Printers Includes:Bolt (1 pcs)Toothed Pulley (1 pcs)Nylon Bushing (1 pcs)  Note: You need one pulley for each belt. Order 2 sets if you need a...

  Idler Set for MakerGear M2 3D Printers Includes:Bolt (1 pcs)Bearings (3 pcs)E-clip (1 pcs) Fits: M2 Rev A through F Note: for the MakerGear M2 Rev G through H, use the M3 idler...