Creator Max

   Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Flashforge Z Motor with Leadscrew (No Nut) Fitment Note: Some older Creator Pro printers use the Dreamer Z motor/lead...

  Flashforge Z Motor with Leadscrew & Nut Fitment Note: Some older Creator Pro printers use the Dreamer Z motor/lead screw, which is a little bit shorter. Please check that your current leadscrew matches the picture...

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

  Flashforge Thermocouple Includes: Thermocouple (1 pcs) Fits: Creator Max

Gates GT2 6MM Belt Sold in lengths of 1 meter Belt width: 6mm The length of the belt you receive will be the quantity you order x1 meter. So, if you order a quantity of 4 you will receive one 4 meter belt.

  Top Cover This is the large clear acrylic cover that goes on the top of the printer. Includes: Top cover (1 pcs) Fits:Creator Pro (2016 or later version)Creator Pro 2Creator MaxCreator Max 2

   *Used Item  Removed from used Creator Pro printers, top covers may be scuffed and show signs of wear, but have no cracks and are in good working condition. Top Cover This is the large clear acrylic cover that goes on the top of...

Tube Grease for lubing the rods and ball screws of your 3D printer. This is the same grease that comes stock with Robo 3D R1+/R2 printers. Includes: Grease (1 pcs) Size: 10g

  Hotend Unclog Pin Helps clear blockages from the hotend Diameter: 1.5mmLength: 133mm Includes: Unclog pin (1 pcs)

  Flashforge Extruder V Bearing Includes: V bearing (1 pcs) Specifications:ID: 3mmOD: 12mmW: 4mmG: 9.5mm Fits:Adventurer 3Adventurer 4Creator 3Creator 3 ProCreator ProCreator Pro 2Creator MaxCreator Max 2DreamerDreamer NXFinder 2Guider 2Guider...

  Flashforge WIFI Board Includes: WIFI board (1 pcs) Fits:Creator MaxInventorDreamerDreamer NX

  Flashforge Wrench  For the heat break on some Flashforge 3D printers Includes: Wrench (1 pcs) Size: 6mm Fits:InventorDreamerDreamer NXCreator ProCreator Max Note This is not a nozzle wrench. Nozzle wrench available here. 

   Used Item:  Removed from low hour 3D printers. Flashforge Stepper Motor - X/Y Axis (Read fit section below) Good quality Moons stepper motors with low hours.  Includes: Stepper motor (1 pcs)Drive pulley (1...

   Used Item:  Removed from low hour 3D printers. Flashforge Stepper Motor - X/Y Axis (Read fit section below) Good quality Moons stepper motors with low hours.  Includes: Stepper motor (1 pcs)Drive pulley (1...

  Y Axis Carriage Bracket - LEFT SIDE ONLY This is the bracket that snaps onto the Y axis linear bearings. The idler pulley and x axis rods attach to this bracket Includes: Bracket (1 pcs) Fits:Creator MaxCreator ProInventorInventor...

Y Axis Carriage Bracket - RIGHT SIDE (Motor Side) This is the bracket that snaps onto the Y axis linear bearings. The motor, limit switch and x axis rods attach to this bracket Includes: Bracket (1 pcs) Fits:Creator MaxCreator...

   Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Y Axis Carriage Bracket - LEFT SIDE ONLY This is the bracket that snaps onto the Y axis linear bearings...

 Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Y Axis Carriage Bracket - RIGHT SIDE (Motor Side) This is the bracket that snaps onto the Y axis linear bearings...

  Linear Rod and Pulley Bracket Holds Y axis rod and pulley in place. Includes: Bracket (1 pcs) Location: Right rear corner only Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2 Note: Does not fit left front/rear or right...

  Linear Rod and Pulley Bracket Holds Y axis rod in place Includes: Bracket (1 pcs) Location:Left RearLeft FrontRight Front Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2 Note: Does not fit right rear corner. If you need...

   Like New  - Removed from new or lightly used printers.  Z Bracket Set These brackets are located at the top and bottom of the z axis and hold the linear rods and leadscrew in place.  Includes: Top bracket (1...

   Used Item  Removed from low hour 3D printer.  Flashforge Z Limit Switch (Endstop) Cable Includes: Cable (1 pcs) Fits:Creator ProCreator MaxDreamerDreamer NXInventor