Guider 2 & 2S (Not HT)

3D Print Removal Tool - Scraper Includes: Scraper (1 pcs)

  Flashforge 3D Print Removal Tool Spatula for removing 3D prints from the build surface. This is the same tool that is provided with many of the new Flashforge 3D printers.  Includes: Spatula (1 pcs)

  Flashforge Extruder Air Duct Fan shroud directs air to the part being printed. Includes:Air duct (1 pcs)Screws (2 pcs) Fits:Guider 2Inventor 2

Air Duct Screw (M3x8) Guider 2/2S, Inventor 2, Finder Holds the plastic air duct in place. Includes: M3x8 screw (2 pcs) Fits:Guider 2Guider 2S HTInventor 2FinderRobo E3 Pro

Microswiss All Metal Hotend Kit - 0.40mm Includes:0.40mm plated brass wear-resistant nozzle (1 pcs)Heat break (1 pcs)Jam nuts - to aid in removing old hotend (1 pcs) Description:The Microswiss all metal hotend allows you to print at much higher...

  Flashforge Bed Leveling Card Includes: Leveling card (1 pcs)

  Flashforge Bed Leveling Hardware  For leveling the build plate.  Includes:Spring (3 pcs)Thumb Nut (3 pcs) Fits: Creator 3Creator 3 ProGuider 2Guider 2S HTRobo E3 Pro

  Flashforge Bed Leveling Sensor Switch Includes: Bed leveling sensor (1 pcs) Fits:Guider 2Guider 2S HTFinderFinder 2Inventor 2Inventor 2SRobo E3 Pro Note: This is the sensor only and does not include the arm or servo. 

  Flashforge Bed Leveling Servo Assembly Includes: Servo assembly (1 pcs)Bed sensor switch (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Bed Leveling Springs - 3 Pack Strong springs for leveling the build plate.  Includes: Spring (3 pcs) Fits: Creator 3Creator 3 ProGuider 2Guider 2S HTRobo E3 Pro

  Flashforge Replacement Drive Belt - X Axis Includes: X axis belt (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Replacement Drive Belt - Y Axis Includes: Y axis belt (2 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Blower (Turbo) Fan This is the fan that blows air on the part being printed. Includes: Fan (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro

Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotend. Contains high quality ZYP™ Boron Nitride and proprietary binders which reduce cracking and flaking when dried...

Brim Scraper (Mini Scraper) We find this tool handy for removing the brim, and purge lines from the build plate. Includes: Brim Scraper (1 pcs)

  Flashforge Flexible Spring Steel Build Plate System Includes:Flashforge print surface pre-installedMagnet sheet with adhesive for easy installation Spring steel flex print surface Max Temperature: 80c Fits:Guider 2S HTRobo E3 ProGuider 2...

  Flashforge Build Plate Frame Includes: Plastic frame (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro Note: You will need this plastic frame if you are installing the flexible build plate on your Guider 2. 

  Flashforge Glass Build Plate Includes: Glass build plate (1 pcs) Dimensions: 310x270x3mm Fits:Guider 2S HTGuider 2 with plastic housing upgradeRobo E3 Pro Note: If you are installing this glass on a Guider 2 you will need to...

  Flashforge PCB Build Plate Heater Includes: PCB heating board assembly (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Button for Touch Screen Includes: Plastic button (1 pcs) Fits:FinderFinder 2Inventor 2Guider 2Guider 2S HTRobo E3 Pro

  C-Clip for Y Axis Bearing Includes: C-Clip (1pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro Note: Each bearing requires 2 clips, be sure to order the quantity you need.  

  Flashforge X Limit Switch Cable (Endstop Cable)  Runs from X axis limit switch to mainboard Includes: Cable (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge V2 Filament Sensor Cable Includes: Cable (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro Note: This will only fit the later version of the Guider printers that have a filament sensor like this one: Guider 2 (2S) Filament...

  Flat Cable for TFT Touch Screen Connects touch screen to mainboard Includes: Cable (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro  WARNING  Pay attention to the orientation of your current cable.Plugging this cable in...

  Flashforge X Motor Cable Includes: Cable (1 pcs) Length: 850mm Fits: Guider 2

  Flashforge Y Limit Switch (Endstop) Cable Includes: Cable (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Y Motor Cable Includes: Cable (1 pcs) Fits:Guider 2

  Flashforge Z Limit Switch (Endstop) Cable Includes: Cable (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro

Guider 2 Camera Bracket STL File  Printable camera bracket for Guider 2S/HT or for adding a camera to the Guider 2. Designed by NSC. Click here to download the STL file. Licensed under a Creative Commons Attribution-ShareAlike 4.0...

Flashforge Ceramic Eye - Filament Guide Includes: Eyelet (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)DreamerGuider 2Guider 2SGuider 2S HTInventorMonoprice VoxelRobo E3

  Flashforge E-Clips For holding timing pulley to 5mm motor and axle shafts Includes: E-Clip (5pcs)

3D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

  Flashforge Extruder Adapter PCB Board Includes: Extruder adapter board (1 pcs)   Fits:Guider 2Guider 2SRobo E3 Pro

  Extruder Cover Includes: Cover (1 pcs) Fits:FinderFinder 2Inventor 2Guider 2Guider 2S HTRobo E3 Pro Note: Mounting hardware not included.

  Flashforge Extruder Cable Runs from the mainboard to the extruder. Includes: Flat Cable (1 pcs) Fits:Creator 3Creator 3 ProGuider 2Guider 2S HTRobo E3 Pro

  Flashforge Extruder Lever Assembly - Left Side  Includes:Filament leverBacking plate assembly (1 pcs)Groove bearing (1 pcs)Groove bearing retaining plate (1 pcs)Shoulder bolt  (1 pcs)Spring  (1...

   Used Item  Removed from low hour 3D printers Flashforge Extruder Lever Assembly - Left Side Includes:Filament lever (1 pcs)Backing plate assembly (1 pcs)Groove bearing (1 pcs)Groove bearing retaining plate (1...

  Flashforge Extruder Spring Includes: Spring (1 pcs) Length: 21.5mm Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Creator 3Creator 3 ProInventorInventor 2FinderFinder 2 Creator ProCreator Pro 2Creator MaxCreator Max...

Flashforge 4020 Fan Cools mainboard and is also the print chamber fan on some printers.  Includes: Fan (1 pcs)Size: 40x40x20mmVolts: 24 VDC Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Adventurer 4InventorInventor...

 Used Item  Removed from low hour 3D printer. Flashforge 4020 Fan Cools mainboard and is also the print chamber fan on some printers.  Includes: Fan (1 pcs)Size: 40x40x20mmVolts: 24 VDC Fits:Adventurer 3Adventurer...

  Flashforge 3010 Fan Includes: Fan (1 pcs)Voltage: 24 VDCSize: 30x30x10mm Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Adventurer 4Adventurer 4 ProGuider 2Guider 2S HTCreator 3 ProRobo E3Monoprice Voxel

  Flashforge 4010 Fan Includes: Fan (1 pcs) Voltage: 24VDC Size: 40x40x10mm Fits: Creator 3Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Hardened Steel Filament Drive (Extruder) Gear Hardened steel for longer life when printing abrasive materials such as Carbon Fiber Nylon Includes:Hardened steel filament drive gear (1 pcs)Set screw (1 pcs) Fits:Guider 2S HTGuider...

  Flashforge Filament Drive (Extruder) Gear Includes:Standard filament drive gear (1 pcs)Set screw (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Creator 3Guider 2S HTGuider 2InventorInventor 2/SFinderFinder 2Creator...

  Flashforge Filament Guide Tube Includes: PTFE tube (1 pcs) Fits: Guider 2Guider 2S HT

Flashforge Filament Sensor Includes: Filament Sensor (1 pcs) Fits: Guider 2Guider2S HTFinder 3Robo E3 Pro Note:This is the V2 filament sensor. Check the photo and make sure it matches your current sensor.Does not include the white PTFE bushing...

  Flashforge Filament Sensor Bracket This bracket is for the V2 filament sensor Includes: Bracket (1pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Flange Bearing (F105ZZ) Includes: Flange bearing (1 pcs) Specifications:ID: 5mmOD: 10mmW: 4mmF: 11.5mm Fits:DreamerDreamer NXCreator ProCreator Pro 2Creator MaxCreator Max 2InventorInventor 2Guider 2Guider 2S HTRobo E3 Pro

  Flashforge 625ZZ Flange Bearing Includes: Flange bearing ( pcs) Location: Y axis Specifications:ID: 5mmOD: 16mmW: 5mm Fits:Creator 3Guider 2Guider 2S HTRobo E3 Pro

Small Phillips Head Screwdriver This is the small screwdriver that comes with the accessory kit of many new Flashforge 3D printers Includes: Screwdriver (1 pcs)

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

Flashforge 3D Printer Grease This is the same grease that comes standard with many Flashforge 3D Printers. Size: 3 Grams Includes: Grease packet (1 pcs)

  Flashforge Heat Break (Threaded Pipe)  Includes: Heat break (1 pcs) Fits:FinderFinder 2.0Inventor 2Inventor 2SGuider 2

Heat Break (Thermal Tube) for Microswiss All Metal Hotend Kit This is a replacement heat break for this Microswiss all metal hotend upgrade. Includes: Heat break (1 pcs) Fits:FinderFinder 2Inventor 2Guider 2

  Flashforge Heater Block  Includes: Heater block (1 pcs) Fits:Guider 2Finder 2Inventor 2 NOTE: Does not include set screw for holding heater cartridge. If needed, purchase set screw here.

  Flashforge Heater Cartridge Includes: Heater cartridge (1 pcs) Volts: 24Watts: 40 Fits:Finder (24 volt)Finder 2Guider 2Guider 2S HTInventor 2Inventor 2SRobo E3 Pro

  Flashforge Heatsink Includes: Heatsink (1 pcs) Fits: Guider 2 Note: Does not include set screw. If needed, purchase set screw here.

PB Select™ Ball End Hex Wrench - L Wrench Includes: Hex wrench (1 pcs) Size: 2.5mm

  Flashforge Hotend Assembly Standard Temperature  Includes: Hotend assembly (1 pcs) Fits: Guider 2  

  Flashforge LED Board - Light Strip Includes: LED light board (1 pcs) Fits:Guider 2Guider 2S HTCreator 3Robo E3 Pro

  Flashforge Limit Switch Includes: Limit Switch (1 pcs) Location: X, Y or Z axis Fits:Finder 3Guider 2Guider 2S HTInventorRobo E3 Pro Fitment Note: Fits different locations on different printers. Make sure the switch in the picture...

MYT LM10UU Linear Bearings Includes: Linear Bearing (4 pcs) Specifications:ID: 10mmOD: 19mmL: 29mm Fits:Guider 2 (X/Y axis)Guider 2S HT (X/Y axis)Prusa MINIPrusa MINI+Sovol SV06 PlusRobo E3 ProOther printers that use LM10UU linear bearings

  Flashforge Linear Rod - Y Axis Includes: Linear rod (1 pcs)  Location: Y Axis Fits:Guider 2Guider 2S HTRobo E3 Pro

  Please read our returns policy regarding electronic items Flashforge Guider 2S Mainboard Includes: Mainboard (1 pcs) Fits: Guider 2S Notes:Not for the Guider 2S HTMake sure your current mainboard has all black stepper drivers. 

Flashforge Metal Hotend Cover Metal shroud fits inside the hotend air duct and protects the heater block. Includes: Hotend shroud (1 pcs) Fits:Guider 2Guider 2S (HT)Inventor 2/SFinder/2Robo E3 Pro

MK10 Brass Nozzle for PTFE Lined Hotend Includes: Nozzle (1 pcs) Size: Select Above Fits:Flashforge Guider 2 (not high temp version)Flashforge InventorFlashforge Inventor 2SFlashforge Creator ProFlashforge Creator MaxFlashforge...

MK10 Brass Nozzle (for Microswiss All Metal Hotend Only) Note: Will not fit the stock PTFE lined hotend. This nozzle has completely different internal dimensions to work with the Microswiss thermal barrier tube...

MK10 Plated Wear-Resistant Nozzle for PTFE-Lined Hotend  This nozzle is for PTFE lined hotends only. It has a larger diameter hole in the top, so the PTFE tube can slide into the nozzle. It will not work with all metal hotends...

Microswiss MK10 Wear-Resistant (A2 Tool Steel) Nozzle for Microswiss All Metal Hotend Kit  Perfect for printing abrasive material, such as carbon fiber, metal filled, wood-filled, glow in the dark, etc. *Note: This...

MK10 Plated Wear-Resistant Nozzle for Microswiss All Metal Hotend Kit If you are printing abrasive material, such as carbon fiber, stainless steel, wood-filled or any other metal filled filaments, this will greatly improve the life of your...

  Timing Belt (Motor) Drive Pulley This is the drive pulley that is used on many Flashforge 3D printers. Includes:Pulley (1pcs)Pulley disc (1 pcs)E-clip (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Creator ProCreator Pro...

  Shock Absorbing Motor Mount For the Y axis stepper motor Includes: Motor mount (1 pcs) Fits:Creator 3Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Brass Nozzle Includes: Brass nozzle (1 pcs) Orifice Size: 0.40mm Note: PTFE tube not included - use the links below to buy the proper PTFE tube for your printer Fits:Guider 2 (not for HT version) - PTFE tubeInventor...

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

PEI Print Surface Adhesive backed. Can be cut to size for smaller beds. Includes: PEI Sheet (1 pcs) Specifications:Material: ULTEM™ 1000Dimensions: 264x306mmThickness: 175um Fits: Guider 2Guider 2S HTGuider 3 -  Note: this is a...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

  Flashforge Power Inlet & On/Off Switch Includes:Power inlet with switch (1 pcs)Fuse (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Guider 2SRobo E3 Pro

   Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Flashforge Power Inlet & On/Off Switch Includes:Power inlet with switch (1 pcs)Fuse (1 pcs) Fits:Creator ProCreator...

  Flashforge Replacement Power Supply (PSU) Includes: Power supply (1 pcs) Fits: Creator 3Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Print Surface (Bed Tape) Adhesive backed for easy application Includes: Print Surface (1 pcs) Size: 263x307mm (can be trimmed to fit other printers) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Extruder/Nozzle PTFE Tube This is the PTFE tube that goes in the nozzle/heat break Includes: PTFE tube (1 pcs) Length: 43mm Fits: Guider 2 (standard temp)

  Flashforge Idler (Driven) Pulley Assembly Includes:Pulley (1 pcs)29mm shaft (1 pcs)10mm Flange Bearing (2 pcs)E-clip (2 pcs) Location: X axis Fits:Guider 2Guider 2S HTRobo E3 Pro Note: This pulley uses 10mm flange bearings and will...

  Flashforge Idler (Driven) Pulley Assembly Includes:Pulley (1 pcs)35mm shaft (1 pcs)Spacer (1 pcs)10mm Flange Bearing (2 pcs)E-clip (2 pcs) Location: Y-Axis Fits:Guider 2Guider 2S HT Note: These pulleys use 10mm flange bearings and only...

  Flashforge Y Axis Drive Pulley Assembly This is the drive pulley with coupler for the newer style stepper motor/shaft. This uses a coupler (included) to connect the drive shaft to the pulley assembly. Includes: Pulley Assembly (1...

M4X4 Set Screw Used to secure the heater cartridge and heatsink of many Flashforge 3D printers. Includes: M4x4 set screw (1 pcs) Specs:12.9 GradeCup PointUses 2mm Hex Key Driver (not included) Fits:FinderFinder 2Guider 2Guider 2S...

  Silicone Sock (Heater Block Cover) The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep...

  Silicone Sock (Heater Block Cover) The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep...

  Flashforge Spool Holder Includes: Spool holder (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Robo E3 Pro   Guider 2S HT (with rectangular opening for spool holder)

   Used Item  Cables are removed from low hour 3D printers. Flashforge Spool Holder Includes: Spool holder (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Robo E3 Pro   Guider 2S HT (with...

  Flashforge Stepper Driver Includes:Stepper Driver (1 pcs)Heatsink (1 pcs) Fits:Guider 2 (All Axis)Guider 2S HT (Z Axis Only)Robo E3 Pro Stepper driver may look different than pictured

  Flashforge Extruder Stepper Motor Includes:  Motor (1 pcs) Location: Extruder Fits: Guider 2Guider 2S (not for Guider 2S HT)Creator 3 (for left or right extruder)

  Flashforge X Axis Stepper Motor Includes: Stepper motor (1 pcs) Location: X axis Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Y Axis Stepper Motor (V2) Includes: Motor (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro Notes: This Y motor is for the later version of the Guider 2 and 2S HT. The later version uses a coupler to connect the left side...

  Flashforge Z Axis Stepper Motor Includes:Z axis motor with leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

  Flashforge Thermocouple Includes: Thermocouple (1 pcs) Fits:Inventor 2Guider 2Guider 2S HTRobo E3 ProFinder*  *IMPORTANT  If ordering for the Finder, please read everything below before ordering.Make sure the picture above...

Gates GT2 6MM Belt Sold in lengths of 1 meter Belt width: 6mm The length of the belt you receive will be the quantity you order x1 meter. So, if you order a quantity of 4 you will receive one 4 meter belt.

  Top Cover This is the large plastic cover that goes on the top of the printer. Includes: Top cover (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro