Printer Parts

  Flashforge Bed Leveling Sensor Switch Includes:Sensor switch (1 pcs)Plastic housing (1 pcs) Fits: Creator 3 (with 3 wire switch) Note: Important! This is for the later version Creator 3 which has the 3 wire switch. If your current switch has...

  Flashforge Bed Leveling Sensor Switch Includes: Sensor (1 pcs)Sensor bracket (1 pcs) Fits: Creator 4

  Flashforge Bed Leveling Sensor Switch Includes: Sensor (1 pcs) Fits:Guider 3Guider 3 PlusRobo E4 Pro 

  Flashforge Build plate Tray This is the tray that the build plate slides into.  Includes: Tray (1 pcs) Fits: FinderFinder 2

  Flashforge Build Plate Bearing Guide Tape - 2 pack This is the clear tape that goes under the built plate tray which the bearing rides on.  Includes: Tape (2 pcs) FitsAdventurer 3 (all versions)Robo E3MP Voxel

  Extra FlexPlate Note: This is not the Complete Builtak Flexplate System. This is the FlexPlate only and requires a magnetic mounting base and print surface. - Specially-coated FlexPlates are resistant to rust and work on...

Extra FlexPlate Please Note: This is not the Complete Builtak Flex System. This is the FlexPlate only and requires a magnetic mounting base and print surface. Specially-coated FlexPlates are resistant to rust and work on both heated...

  Replacement BuildTak FlexPlate for Robo R2 Flexplate System Includes: FlexPlate (1 pcs) Size 9x9in Fits: Robo R2 Please Note: This is not the Complete Builtak FlexPlate System. This is an individual replacement...

BuildTak FlexPlate System Size: 165x165mm (6.5x6.5in) Includes:  Original BuildTak print surface (1 pcs) Spring steel sheet (1 pcs) Magnetic base (1 pcs) Fits:  Ender 2 printers with a 165x165 print bed

BuildTak FlexPlate System Size: 235x235mm (9.25x9.25in) Includes:  Original BuildTak print surface (1 pcs) Spring steel sheet (1 pcs) Magnetic base (1 pcs) Fits:  Ender 3 printers with a 235x235 print bed

Robo R2/C2 Bushing Block  Also known as the carriage bracket Includes: Bushing block (1 pcs) Fits:Robo R2Robo C2  Use with R2/C2 Bushings Note: Once installed, it is not possible to remove the bushing blocks without damaging them. 

  Button for Touch Screen Includes: Plastic button (1 pcs) Fits:FinderFinder 2Inventor 2Guider 2Guider 2S HTRobo E3 Pro

  C-Clip for Y Axis Bearing Includes: C-Clip (1pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro Note: Each bearing requires 2 clips, be sure to order the quantity you need.  

Ribbon cable for Robo C2 Runs from mainboard to extruder assembly.  Includes: Cable (1 pcs) Fits: C2

PB Select™ Heat Bed Power Cable This is the cable that runs from the mainboard to heated bed on the Prusa MINI and MINI+ Includes: Cable (1 pcs)Terminal block plug (1 pcs) Specs:Wire: 16 awgLength: 18 inches (approximately)Ring terminals:...

PB Select™ Heatbed to Einsy power cable for Prusa (screw-attached type) Runs from mainboard to heated bed.  Includes: Cable (1 pcs) Fits:MK3MK3SMK3S+ Note: Attachment screws not included To replace this part, please consult...

PB Select™ Heat Bed Power Cable This is the cable that runs from the Mainboard to the heated bed on Prusa MK2 series Note: ONLY compatible with the heated beds with detachable power cable. NOT compatible with heated beds where the power cable is...

Mainboard to Uptown Board Wire (cable) This cable runs from the C2 mainboard to the extruder heater connection on the uptown board. Includes: Cable (1 pcs) Fits: C2

Prusa IR Filament Sensor-Einsy Cable Runs from filament sensor to mainboard. Includes: Cable (1 pcs) Fits: MK3 To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow the manual for your printer model.

PB Select™ Cable for IR Filament Sensor to Einsy Board Runs from filament sensor to mainboard. Includes: Cable (1 pcs) Fits:MK3SMK3S+ To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow...