Printer Parts

MR85ZZ Ball Bearings High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (2 pcs) Specifications:ID: 5mmOD: 8mmW: 2.5mm Note: Does not fit the new BMG IDGA extruders

Bondtech Ball Bearing High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 8MMW: 2.5mm Note: Not for use with the IDGA extruders.

MR95ZZ  Bearing for Titan and Titan Aero Extruder Includes: Bearing (2 pcs) Specifications:ID: 5mmOD: 9mmW: 3mmMR95ZZABEC 5 Fits: TitanTitan Aero

  Flashforge Bearing Clamp This little plastic part clamps the bearing to the bracket. Includes: Plastic clamp (1 pcs) Fits:DreamerDreamer NXInventor Note: Mounting screws not included

Prusa MINI Bearing Clips Includes: Bearing Clip (3 pcs)Screws (6 pcs)Nyloc Nuts (6 pcs) Note: Bearings not included. Fits:MINIMINI+ To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow...

Bearing Clips for Prusa MK4 Includes: Bearing Clip (3 pcs)Bearing pad - plastic (3 pcs)Bearing pad - rubber (3 pcs)Screws (6 pcs) Fits:MK3.9MK3.9SMK4MK4S Note: Bearings not included To replace this part, please consult the...

Bearing Clips for Prusa MK3S+ Includes: Bearing Clip (3 pcs)Screws (6 pcs)Nyloc Nuts (6 pcs) Fits:MK3S+ Note: Bearings not included To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow...

PB Select™ Bearing Clips for Prusa MK3S+ Includes: Bearing clip (3 pcs)Screws (6 pcs)Nyloc Nuts (6 pcs) Fits: MK3S+ To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow the manual for...

  Flashforge Bearing (105ZZ) This is the bearing that goes on the inner side of the pulley on the Y axis drive shaft. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 10mmW: 4mm Fits:DreamerDreamer NXInventor Note: Sold in units...

  Bearing Under Build Tray This bearing is located on the underside of the build plate tray. Specifications:ID: 4mmOD: 12mmW: 4mm Includes: Bearing (1 pcs) Fits: Adventurer 3 (all versions)Monoprice VoxelRobo E3

Robo R1+ Heated Bed Connection Cable  You will need this extension cable if you are upgrading from a v1 bed (with a long cable) to the v2 bed (which has a short cable).  Includes: Cable (1 pcs) Fits: Robo R1+ with v2 bed

R2 Bed Connection Cable  Includes: Cable (1 pcs) Fits: R2 (only fits v2 heated bed)

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available separately here

Artillery Silicone Heater for Print Bed Includes:110v Silicone Heater (1 pcs)220x220x7mm Thermal Insulation (1 pcs) Voltage: 110 VAC Fits: Genius

Silicone Heater Kit for Print Bed Includes: Silicone Heater (1 pcs)220x220x7mm Insulation pad (1 pcs) Voltage: 110 VAC Fits: Genius Pro

Artillery Silicone Heater for Print Bed Includes:Silicone Heater (1 pcs)300x300 adhesive backed insulation (1 pcs) Voltage: 110 VAC Fits: Sidewinder X1 Note: Artillery now uses the X2 insulation pad for this X1 bed heater (the X1-specific...

Silicone Heater for Print Bed Includes: Silicone Heater (1 pcs)300x300x7mm Thermal Insulation (1 pcs) Voltage: 110 Fits: Sidewinder X2

Bed Heater Includes: Heater (1 pcs)Magnet sheet - attached (1 pcs) Voltage: 110 VAC Fits: Sidewinder X3 Plus

Bed Heater Includes: Heater (1 pcs)Magnet - installed (1 pcs) Voltage: 110 VAC Fits: Sidewinder X3 Pro

Bed Heater Includes: Heater (1 pcs)Magnet - Installed (1 pcs)Insulation pad - installed (1 pcs) Voltage: 110 VAC Fits: Sidewinder X4 Plus