Robo 3D
-
Print Surface (Bed Tape) for Robo E4 - 235x235mm
Robo 3D
$12.95Robo Print Surface (Bed Tape) Adhesive backed for easy installation Includes: Print surface sheet (1 pcs) Size: 235x235mm Fits: Robo E4$12.95 -
Bare Hotend - R1/+, R2, C2 | Robo 3D
Robo 3D
Now: $19.95Regular Price: $24.95Robo Hexagon Hot End (Bare Unit) For 1.75mm filament Includes:Heatsink (1 pcs)Heat break (1 pcs)Heater block with set screws (1 pcs)0.40mm brass Nozzle (1 pcs) Fits: Robo R1Robo R1+Robo...Now: $19.95Regular Price: $24.95 -
$29.95
-
Motor Mount - X/Y Axis - C2 | Robo 3D
Robo 3D
$4.95NEMA17 Stepper Motor Mount Includes: Motor mount (1 pcs) Fits: C2$4.95 -
$4.95
-
Cable for Thermistor - R1/+ | Robo 3D
Robo 3D
$3.95R1+ Thermistor Cable (wire) Runs from mainboard to thermistor.Will also work for the heatsink fan or print cooling fan but pay attention to the orientation of the plug (at the mainboard) so...$3.95 -
Cable - Heater Cartridge - MB to Uptown Board - C2 | Robo 3D
Robo 3D
$5.95Mainboard to Uptown Board Wire (cable) This cable runs from the C2 mainboard to the extruder heater connection on the uptown board. Includes: Cable (1 pcs) Fits: C2$5.95 -
Print Bed Plastic Housing - R2 | Robo 3D
Robo 3D
$14.95Print Bed Plastic Housing for Robo R2 Includes: Plastic bed housing (1 pcs) Notes: This is the plastic housing only.Does not include screws: Reuse the screws from your old bed. Does...$14.95 -
$3.95
-
3mm Bed Magnets (4 Pack) - R1+ | Robo 3D
Robo 3D
$3.493mm Bed Magnets for R1/+ Glass Bed Apply using epoxy and clamps for best results. Includes: Magnet (4 pcs) Fits:Robo R1Robo R1+ Note: These magnets are 3mm thick and do not work with...$3.49 -
Ferrite Core Anti-Interference Ring - 4mm
Robo 3D
$2.99Ferrite Core Anti-Interference Ring Includes: Ferrite ring (1 pcs) Fits wire up to 4mm$2.99 -
Cable - Z Motor to Mainboard - R2, C2, R1/+ | Robo 3D
Robo 3D
$6.95Z Motor Cable This cable is for the R2, but also works for the C2 and R1/+ Includes: Cable (1 pcs) Length: 600mm Fits: R2C2R1/+$6.95 -
Raspberry Pi Supports (4 Pack) R2, C2 | Robo 3D
Robo 3D
$2.99Standoffs for Mounting Raspberry Pi Includes: Standoff (4 pcs) Fits:Robo R2Robo C2$2.99 -
Cable for Print Cooling Fan - R1+ | Robo 3D
Robo 3D
$4.95R1+ Fan Cable (Wire) Runs from mainboard to print cooling fan. Will also work for the heatsink cooling fan, but the wires will need to be reversed or the fan runs backwards. ...$4.95 -
Fan for Print (Part) Cooling - R1/+ | Robo 3D
Robo 3D
$8.95Robo R1+ Print Cooling Fan This is the fan that cools the part being printed. Includes: Fan (1 pcs) Amps: 0.08 Fits:Robo R1Robo R1+ Note: The color of the plug may differ from the photo above...$8.95 -
Fan for Bottom Cover - R1/+ | Robo 3D
Robo 3D
$8.95Robo R1+ Bottom Cover Fan for Cooling Electronics This is the fan that cools the Arduino and RAMPs board in the bottom of the printer Includes: Fan (1 pcs) Amps: 0.08 Fits:Robo R1Robo R1+ Note:...$8.95 -
Cable for Power Supply - R1/+ | Robo 3D
Robo 3D
$9.95Power Supply Cable This cable runs from the power inlet to the power supply of the Robo R1+ Includes: Cable (1 pcs) Fits:Robo R1Robo R1+$9.95 -
Z Carriage (Motor Side) R1+ | Robo 3D
Robo 3D
$15.95Motor Side Z Carriage for Robo R1+ Replacement z axis carriage with motor mount for Z-axis. Includes: Carriage (1 pcs) Location Motor Side (1 pcs) Fits: R1+ Note This is the carriage...$15.95 -
Z Carriage (Idler Side) R1+ | Robo 3D
Robo 3D
$15.95Idler Side Z Axis Carriage for Robo R1+ Replacement Z Carriage for the idler side Z-axis (non motor side) Includes: Carriage (1 pcs) Location: Idler Side Fits: R1+ Note: This is the...$15.95 -
Doorstop With Magnets - R2 | Robo 3D
Robo 3D
$7.95Doorstop for Robo R2 Includes: Door stop (1 pcs)Magnets (2 pcs) Fits: Robo R2$7.95