Robo 3D

  Flashforge Build Plate Frame Includes: Plastic frame (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro Note: You will need this plastic frame if you are installing the flexible build plate on your Guider 2. 

  Flashforge Glass Build Plate Includes: Glass build plate (1 pcs) Dimensions: 310x270x3mm Fits:Guider 2S HTGuider 2 with plastic housing upgradeRobo E3 Pro Note: If you are installing this glass on a Guider 2 you will need to...

Flashforge Build Plate Heater for Removable (Flexible) Print Surface This aluminum heater goes under build plate. Includes: Build plate heater (1 pcs)  Size: 164*168mm Note: Only fits printers with removable print bed...

Build Plate Heater for Glass Print Surface This aluminum heater goes under glass build plate. Includes: Heater plate (1 pcs)  Note: Only fits printers with glass print bed. Does not fit printers with removable...

Build Plate Heater Includes: Heater (1 pc)Magnet - Installed (1 pc) Fits: Adventure 5MAdventure 5M ProRobo E4

  Flashforge PCB Build Plate Heater Includes: PCB heating board assembly (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Build Plate Heater Includes: Silicone heater (1 pcs) Fits: Guider 3Robo E4 Pro

  Flashforge Build Plate Latch/Handle Includes: Plastic latch (1 pcs) Fits:Adventurer 3Monoprice VoxelRobo E3 Note: Screws not included

  Flashforge Bed Leveling Sensor Switch Includes: Sensor (1 pcs) Fits:Guider 3Guider 3 PlusRobo E4 Pro 

  Flashforge Build Plate Bearing Guide Tape - 2 pack This is the clear tape that goes under the built plate tray which the bearing rides on.  Includes: Tape (2 pcs) FitsAdventurer 3 (all versions)Robo E3MP Voxel

  Extra FlexPlate Note: This is not the Complete Builtak Flexplate System. This is the FlexPlate only and requires a magnetic mounting base and print surface. - Specially-coated FlexPlates are resistant to rust and work on...

  Replacement BuildTak FlexPlate for Robo R2 Flexplate System Includes: FlexPlate (1 pcs) Size 9x9in Fits: Robo R2 Please Note: This is not the Complete Builtak FlexPlate System. This is an individual replacement...

Robo R2/C2 Bushing Block  Also known as the carriage bracket Includes: Bushing block (1 pcs) Fits:Robo R2Robo C2  Use with R2/C2 Bushings Note: Once installed, it is not possible to remove the bushing blocks without damaging them. 

  Button for Touch Screen Includes: Plastic button (1 pcs) Fits:FinderFinder 2Inventor 2Guider 2Guider 2S HTRobo E3 Pro

  C-Clip for Y Axis Bearing Includes: C-Clip (1pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro Note: Each bearing requires 2 clips, be sure to order the quantity you need.  

Ribbon cable for Robo C2 Runs from mainboard to extruder assembly.  Includes: Cable (1 pcs) Fits: C2

Mainboard to Uptown Board Wire (cable) This cable runs from the C2 mainboard to the extruder heater connection on the uptown board. Includes: Cable (1 pcs) Fits: C2

Cable - IR Sensor to Downtown Board For connecting IR Bed Level Sensor to Downtown Board  Includes: Cable (1 pcs) Fits: Robo R2Robo C2

SD to RAMPs cable Connects SD card reader to RAMPs board. Includes: Cable (1 pcs) Fits:Robo R1Robo R1+

Extruder Motor Cable for Robo R2 and C2 3D Printers Includes: Cable (1 pcs) Fits: R2C2