Robo 3D

Robo R1+ Extruder Bracket  Includes: Bracket (1 pcs) Fits:Robo R1Robo R1+ 

Robo Fan Bracket  This is the bracket that holds the heatsink cooling fan Includes: Bracket (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Extruder Lever Axle Shaft  Includes: Shaft (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Hotend Quick Release Plate This plate locks the hotend in place. Hardware not included.  Includes: Hotend plate (1 pcs) Fits: Robo R1Robo R1+ 

GT Belt for Robo C2  Includes: Belt (1 pcs) Size: 6x466mm Fits:Robo C2

Robo C2 Belt This is the short belt that runs from the stepper motor to the X/Y axis shaft. Includes: Belt (1 pcs) Length: 260mm Fits: Robo C2

Robo R1+ Y Axis Belt  Includes: Belt (1 pcs) Location:  Y axis Length: 500mm Fits: Robo R1Robo R1+ 

Robo R1+ Filament Guide Includes: Plastic guide (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Big Extruder Drive Gear  Includes: Gear (1 pcs) Fits:Robo R1Robo R1+ 

Robo R1+ Small Extruder Drive Gear Includes: Gear (1 pcs) Fits:Robo R1Robo R1+ 

Robo Z Axis Linear Bearing Includes: Bearing (1 pcs) Specifications:ID: 12mmOD: 21mmL: 57mmF: 32mm Fits:Robo R2Robo C2     

Robo R2/C2 Bushing Block  Also known as the carriage bracket Includes: Bushing block (1 pcs) Fits:Robo R2Robo C2  Use with R2/C2 Bushings Note: Once installed, it is not possible to...

Robo R1+ X Carriage with Bearings  This is the bracket the extruder rides on. Includes: Carriage (1 pcs)Bearings (4 pcs) Fits:Robo R1Robo R1+ Note: this latest batch came bulk packaged, so...

Robo Brass Bushing - 4 Pack Includes: Bushing (4 pcs) Specifications:ID: 8mmOD: 11.7mmL: 36mm Fits:Robo R2Robo C2

Robo Extruder Wiring Harness  Runs from mainboard to extruder Includes: Wiring harness (1 pcs) Fits: R2

Robo Extruder Latch  Includes:  Latch (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Y Belt Clamp - 2 Pack Includes: Belt clamp (2 pcs) Location: Y belt Fits:Robo R1Robo R1+

Robo Filament Sensor Block (cover) Includes: Sensor block (1 pcs) Fits:Robo R2Robo C2 Note: This is the replacement filament sensor block only.

Robo Hobbed Bolt v2 This hobbed bolt has a wider filament path than the v1 (the v1 is no longer available). Includes: Hobbed bolt (1 pcs) Fits:Robo R1Robo R1+

Y Bracket for Robo R1+ These brackets connect the two Y-Axis rods that the bed travels on.  Note: Magnets will need to be glued in, in the appropriate orientation for your glass bed. We...