Robo

  Flashforge Nozzle Temperature Sensor (Thermocouple) Includes: Temperature sensor (1 pcs) Fits:Guider 3Guider 3 PlusRobo E4 Pro

*Clearance item, no returns Limit Switch (endstop) Includes: Limit switch (1 pcs) Location: X/Y Axis Fits:Robo R1Robo R1+ 

  Flashforge Nozzle Heating PCB Board Also called the nozzle adapter board Includes: PCB Board (1 pcs) Fits: Adventurer 3Adventurer 3 Pro (not Pro 2)Monoprice VoxelRobo E3

BuildTak PEI Sheets Size: 235x235mm (9.25x9.25 inches) Includes: PEI Sheet (2 pcs) Fits:Creality Ender 3 seriesAny 3D printer with a 9.28x9.25 inch print bed Manufactured right here in the USA to ensure consistent quality and composition,...

PEI Print Surface Adhesive backed. Can be cut to size for smaller beds. Includes: PEI Sheet (1 pcs) Specifications:Material: ULTEM™ 1000Dimensions: 264x306mmThickness: 175um Fits: Guider 2Guider 2S HTGuider 3 -  Note: this is a...

Raspberry Pi Power Cable This is the cable that runs from the mainboard to the Raspberry Pi. It is a little shorter then the stock R2 cable, but will reach with slightly less excess wire. Includes: Cable (1 pcs) Fits:Robo R2Robo C2

  Flashforge Power Inlet & On/Off Switch Includes:Power inlet with switch (1 pcs)Fuse 8A (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Guider 2SRobo E3 Pro

   Used Item  Removed from low hour 3D printer. May have minor scratches and/or cosmetic imperfections. Flashforge Power Inlet & On/Off Switch Includes:Power inlet with switch (1 pcs)Fuse 8A (1 pcs) Fits:Creator...

  Flashforge Power Supply Includes: Power supply (1 pcs) Fits:Adventurer 3Adventurer 3 Pro (not Pro 2)Monoprice VoxelRobo E3

Power Supply for Robo R1+ 3D Printer Includes: Power supply (1 pcs) Specifications:Volts: 12 VDCWatts: 400 Fits: Robo R1Robo R1+

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

Power Supply Includes:Power supply unit (1 pcs)Cable (1 pcs) Voltage: 19 VDC Fits: Robo C2

  Power Supply Unit (PSU) Includes: PSU (1 pcs) Fits:Adventurer 5MAdventurer 5M ProRobo E4

Print Bed Plastic Housing for Robo R2 Includes: Plastic bed housing (1 pcs) Notes: This is the plastic housing only.Does not include screws: Reuse the screws from your old bed. Does not include magnets: Reuse the magnets...

  Flashforge X Carriage (Print Head Mounting Bracket) This is the bracket the print head mounts to and slides back and forth on the X carriage.  Includes: Bracket (1 pcs) Fits: Adventurer 3Adventurer 3 ProRobo E3Monoprice Voxel Note:...

Robo Print Surface (Bed Tape) Adhesive backed for easy installation Includes: Print surface sheet (1 pcs) Size: 235x235mm Fits:  Robo E4

  Flashforge Print Surface (Bed Tape) Adhesive backed for easy application Includes: Print Surface (1 pcs) Size: 263x307mm (can be trimmed to fit other printers) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Print Surface (Bed Tape) Adhesive backed for easy installation Includes: Print surface sheet (1 pcs) Fits: Guider 3Robo E4 Pro 

  Flashforge PTFE Tube Runs from the filament feeder (extruder) to the print head. Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Monoprice VoxelRobo E3 Note: Does not include snap ring Watch the videos below for helpful information on...

  Flashforge Hotend/Nozzle PTFE Tube This the PTFE tube that goes inside the heatsink.  Includes: PTFE tube for hotend (1 pcs) Length: 26.75mm Fits: Guider 2S HTRobo E3 Pro