Robo

Robo R1+ Spool Holder  Includes: Spool holder (1 pcs) Fits:Robo R1Robo R1+  Note: These are new, but this recent batch is older stock that has minor scuffing from storage.

Short Spool Holder for Robo C2 Includes: Spool holder (1 pcs) Total length: 4.20 inchesHolds up to: 3.75 inch spool Fits: C2

Stainless Steel Nozzle Includes: Nozzle of selected size (1 pcs) Material: Stainless Steel Fits:Guider 3Guider 3 PlusCreator 3 Pro (does not fit standard Creator 3)Creator 4Robo E4 Pro

Artillery GT2 Pulley (Steel) Steel timing pulley Includes:Pulley (1 pcs)Set Screws (2 pcs) Fits: 8mm Shaft Specs:20 Tooth7mm Wide (for 6mm belt)8mm BoreSteel

  Flashforge Stepper Driver Includes:Stepper Driver (1 pcs)Heatsink (1 pcs) Fits:Guider 2 (All Axis)Guider 2S HT (Z Axis Only)Robo E3 Pro Stepper driver may look different than pictured

  Flashforge Extruder Stepper Motor Includes: Motor (1 pcs) Location: Extruder Fits: Guider 2S HTRobo E3 Pro

  Flashforge X Axis Stepper Motor Includes: Stepper motor (1 pcs) Location: X axis Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Y Axis Stepper Motor (V2) Includes: Motor (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro Notes: This Y motor is for the later version of the Guider 2 and 2S HT. The later version uses a coupler to connect the left side...

  Flashforge X/Y Motor Includes: Stepper motor (1 pcs) Fits: Guider 3Guider 3 PlusGuider 3 UltraRobo E4 Pro 

  Flashforge Z Axis Stepper Motor Includes:Z axis motor with leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Z Motor Includes: Z axis motor with leadscrew (1 pcs)Leadscrew Nut (1 pcs) Fits: Guider 3, Robo E4 Pro

  Flashforge Stepper Motor (X/Y/Z) Includes: Stepper motor (1 pcs) Location: X/Y/Z Axis* Fits: Finder *(X/Y Axis Only)Finder 2 *(X/Y Axis Only)Adventurer 3 (X/Y/Z)Adventurer 3 Pro (X/Y/Z)Adventurer 3 Pro 2 (X/Y/Z)Adventurer...

  Flashforge Extruder Stepper Motor Includes: Stepper motor (1 pcs) Location: Extruder (Filament Feeder) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Monoprice VoxelRobo E3

Nema17 Stepper Motor for Robo R2 and C2 3D Printers Includes:Motor (1 pcs)Filament drive gear - installed (1 pcs) Fits: Robo R2Robo C2*Robo R1/+ (X/Y Axis Only) **Notes: This motor will work for the X and Y axis of all the above printers...

  Flashforge X Axis Stepper Motor Includes:Stepper motor (1 pcs)Drive pulley (1 pcs) Fits: Guider 2S HTRobo E3 Pro

Nema17 Stepper Motor For the X/Y and Extruder axis of the R1/+, R2 and C2 3D printers. Includes: Motor (1 pcs) Fits:Robo R2Robo C2Robo R1Robo R1+

  Hotend Support Pins These pins go between the heater block and heatsink. Includes: Pin (6 pcs) Fits:Creator 3 ProGuider 3Guider 3 PlusRobo E4 Pro Note: Hotend in picture is not included

Super Lube® 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality grease...

Super Lube® 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease. Includes: 1...