Parts & Accessories

PB Select™ Stepper Motor Mount CNC machined 3 mm thick in lightweight aluminum, assuring a secure and stable mount for your BMG extruder. Includes: Motor mount (1 pcs) Fits:Bondtech BMGNEMA 17 Stepper Motor

Bearing for DDX Direct Drive Extruder & IDGA Ball bearing to use in Bondtech DDX Direct Drive eXtruder Includes: Bearing (1 pcs) Specifications:ID: 4mmOD: 8mmW: 3mm Fits:DDXIDGA

MR85ZZ Ball Bearings High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (2 pcs) Specifications:ID: 5mmOD: 8mmW: 2.5mm Note: Does not fit the new BMG IDGA extruders

Bondtech Ball Bearing High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 8MMW: 2.5mm Note: Not for use with the IDGA extruders.

This mount for the BMG extruder is CNC machined to precise tolerances in 3 mm thick aluminum, assuring a secure and stable mounting for your extruder.

Bondtech Shaft Assembly for BMG (Bondtech Mini Geared) Extruder Includes:Shaft AssemblySet screw for 1.75/5.0 drive gear* *Drive gear not included

Adapter Direct - Bowden for 3mm diameter filament CNC-machined in aluminum with a mounted push-fit connector for 6mm tube. Use this adapter in the groove mount where the hot-end is located to fit your Bowden tube - see center image below.

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side ...

Bondtech JST-XH4 Cable JST-XH4 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side   ...

Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...

E3D Collet Clip Only fits this collet for 4 mm PTFE Tube. Includes: Collet clip (2 pcs) FitsE3D V6E3D Revo SixE3D Revo MiniE3D CRPrusa Bondtech

Slice Engineering Copperhead Heat Break for Prusa MINI/MINI+ The Copperhead Prusa MINI heat break is bimetallic, made of a copper outer body and an interior steel needle, which gives this heat break better cooling performance, allowing for a...

  E3D Thermistor Cartridge  Cartridge type Semitec 104NT thermistor suitable for all E3D (and other) hotends using a cartridge type heater block. Includes: Thermistor (1 pcs) Specs:Max temperature: 300°CCartridge diameter:...

Extension Cable for Bondtech DDS on Creality CR10S  Extension cable to use the Bondtech Creality CR10S Direct Drive Extruder on the S4 and S5 models.  This will extend the existing cables 40 cm...

Bondtech Stainless Steel Heat Break Kit for Prusa MINI and MINI+ Stainless Steel heat break for the Prusa Mini. Solves the heat-creep issues revealed during the extensive testing Bondtech performed on the Prusa Mini. The adjusted length of the...

Heater Cartridge for Bondtech LGX Artillery Replacement 24v 50W heater for LGX Mosquito For Sidewinder. Includes: Heater cartridge (1 pcs) Fits the following Artillery printers:Sidewinder X1Sidewinder X2With the following Bondtech print...

Heater Cartridge Repair Set for DDS Gen I Fits: 1st Generation DDS for CR-10S Included in this set: 1x 12v 40W Heater Cartridge 2x black nylon zip ties 8 cm of shrinking tube 11 cm of soldering wiring Step by Step Guide Please check how to make the...

Heavy Duty Metal Push Fit Connector  All Metal For 4mm Tube Thread G1/8″  Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube section

Bondtech Heavy Duty Metal Push Fit Connector  All Metal For 4mm Tube Thread G1/8″  Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube section

PB Select™ M3 Stainless Steel Square Nuts These thin square nuts work in many applications that require a thinner (1.75mm) square nut. Including E3D Hemera Stepper Motors, Prusa Printers and Bondtech Extruders. Includes: Square Nut (10 pcs)...