Bondtech & Compatible

Bondtech LGX™ Extruder for Prusa MK3S/+ and Mosquito This LGX™ upgrade kit is for Prusa MK3S/MK3S+ printers that have Slice Engineering Mosquito or Mosquito Magnum hotend. Includes: LGX™...

Bondtech LGX™ Drive Gear (Wheel) Made of hardened steel Fits: Bondtech LGX™ Large Gears eXtruder

Bondtech LGX™ Mounting Accessories Spare parts set for the Bondtech LGX™ Large Gears eXtruder Includes: 3x M3x30 Low Head Screw 4x M3x18 Motor Studs with M3x4 mounting thread 1x 30mm PTFE Tube Extend the possibilities of...

Bondtech LGX™ Secondary Gear Made of self lubricant high temperature plastic to replace a secondary gear on the Bondtech LGX™ Large Gears eXtruder Includes:  Secondary Gear (1pcs) Fits: Bondtech LGX™ Large Gears...

Bondtech LGX™ TPE Lever Grip Replacement Includes: TPE lever grip (1 pcs) Fits: LGX Does not fit LGX Lite

Bondtech LGX™ X-Carriage Prusa MK3S This LGX™ X-carriage is required to install the Bondtech LGX for MK3S & Mosquito Includes: SLS X-Carriage Front (1 pcs)SLS X-Carriage Rear (1 pcs)M3x10 Screws (5 pcs)M3 square nut (5 pcs)M3...

M3 Brass Thread Insert - 4 Pack Size: M3 OD: 4.6mm Length: 5.5mm Recommended hole diameter: 4.0 mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

M3 Brass Thread Insert - 4 Pack Size: M3 OD: 4.6mm Length: 5mm Recommended hole diameter: 4.0 mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

PB Select™ M3 Stainless Steel Square Nuts These thin square nuts work in many applications that require a thinner (1.75mm) square nut. Including E3D Hemera Stepper Motors, Prusa Printers and Bondtech Extruders. Includes: Square Nut (10 pcs)...

M4 Brass Thread Insert - 4 Pack Size: M4 OD: 6mm Length: 5mm Recommended hole diameter: 5.25 mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

M5 Brass Thread Insert - 4 Pack Size: M5 OD: 7.5mm Length: 6mm Recommended hole diameter: 6.75 mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Bondtech M5x10 low head cap screw for Bondtech Extruders, to be used with the M5 thread inserts or similar. Sold in units of one

Black-coated M5x10 low head cap screw to be used with the M5 thread inserts or similar. Sold as a 5 pack

Bondtech Motor Gear for BMG Extruder 17 tooth brass gear with M3x3 set screw. Used in Bondtech BMG single and dual direct extruders. Note: Make sure that the set screw does not collide with the secondary plastic gear when assembled.

Needle Bearings for Bondtech BMG - 2 Pack For shaft diameter of 3mm. High precision needle bearing for Bondtech BMG drive gears. Includes: Needle bearing (2 pcs) Specifications:(Measured by hand - sizes are approximate)ID: 3.1mmOD: 4.9mmL: 6.7mm

22mm Nema 17 Stepper Motor for Bondtech Extruder Nema17 Pancake stepper motor with a 41 cm non-detachable, bare end leads (no plug). Max Input current: 0.8A Step angle: 1.8 deg. Torque: 12 Ncm Outputshaft diameter: 5.0 mm with flat. Hole for...

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D, Nextruder Etc)5.5 mm5.0 mm4.5 mm (Sidewinder X3/X4) Fits:E3D V6 NozzlesPrusa Nextruder standard and highflow nozzles7mm RepRap...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

PTFE Fittings Set for Prusa Mini Use this set to simplify the install, use and maintenance of Prusa Mini’s bowden tube.Instead of using 3 PTFE tube sections, use one only.Includes push-fit collets for ease of use and effective hold of the...