CR-10 Max

X Axis Idler Wheel High hardness, wear resistant POM is CNC precision machined with no burrs or bubbles for a smooth surfaceLow noise high precision smooth roller bearingsQuieter and more wear resistant than standard rollers Includes: Roller wheel...

  PTFE liners for Microswiss Direct Drive Kits and All Metal Hotend (Pack of 5) Capricorn PTFE liners for Microswiss Direct Drive Kits and All Metal Hotend for CR10 and Ender printers. Runs between the extruder and hotend. Includes: PTFE...

PTFE liner for Microswiss Direct Drive Kits and All Metal Hotend Capricorn PTFE liner for Microswiss Direct Drive Kits and All Metal Hotend for CR10 and Ender printers. Includes: PTFE tube (1 pcs) Specifications:50mm long Beveled...

Creality Pneumatic Joint Set  Includes:Small push fit connector (1 pcs)Small clip (1 pcs)Large push fit connector (1pcs)Large clip (1 pcs) Fits:Ender-2Ender-2 ProEnder-3Ender-3SEnder-3 ProEnder-3 V2Ender-3 MaxEnder-4Ender-5Ender-5...

Creality Silicone Pro Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament from...

PB Select™ Silicone Socks - 3 Pack The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep...

Creality 42-40 Stepper Motor Includes: 42-40 Stepper Motor (1 pcs) Below are some of the printers this motor will fit. It may also fit other Creality printers that use the 42-40 stepper motor pictured above Fits: X Axis  CR-10 Max CR-10S Pro V2...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

Tension hardware kit for Direct Drive Extruder This is a spare tension hardware kit for Microswiss Direct Drive kit for CR-10 / Ender printers.  Includes:Tension Pin (1 pcs)Spring (1 pcs)Tension Knob (1 pcs) Fits: Microswiss...

Tension lever for Micro Swiss Direct Drive Extruder This is a spare tension lever for Micro Swiss Direct Drive kit for CR-10 / Ender printers.  Includes:Lever (1 pcs)Gear (1 pcs)Shoulder bolt (1 pcs) Made in the USA

  Creality Thermistor Thermistor has bare wire ends (no installed connector) and comes with heat shrink solder butt connectors. See this video for using the heat shrink solder connectors. Includes: Thermistor (1 pcs)Heat shrink solder butt...

  Creality Yellow Bed Leveling Spring Strong bed springs for Creality and other 3D printers. Fits most Creality printers that use bed springs.  Includes: Spring (1 pcs) Dimensions:Length: 30mm (un-sprung)OD: 8.2mmID:...

Coupler - Stepper Motor to Leadscrew Includes: Coupler (1 pcs) Size:Motor Shaft: 5mmLeadscrew: 8mm Fits:CrealityArtillery

Creality 42-34 (Z) Stepper Motor Includes: Stepper motor (1 pcs) Location: Z Axis Fits:Ender-2 ProEnder-3 S1Ender-3 S2 ProEnder-3 S1 PlusEnder-3Ender-3 NeoEnder-3 V2Ender-3 V2 NeoEnder-3 MaxEnder-3 Max NeoEnder-5 ProEnder-5 PlusCR-6 SECR-6...

Aluminum Alloy Coupling - 2 Pack Anodized aluminum coupling for joining 5mm motor shaft with 8mm leadscrew. Specs: 5mm ID -side A 8mm ID - side B 13.8mm OD 25mm length Includes: Coupling (2pcs) Setscrew (2 pcs) Fits:  Ender-3...