Robo E3

  Flashforge Filament Tension Lever Includes: Plastic lever (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Dreamer (Right Side)Dreamer NXCreator Pro (Right Side)Creator Pro 2 (Right Side)Creator Max (Right...

Small Phillips Head Screwdriver This is the small screwdriver that comes with the accessory kit of many new Flashforge 3D printers Includes: Screwdriver (1 pcs)

  Flashforge FPC Flat Cable for Build Plate Heater Runs from heated build plate to mainboard. Includes: FPC Cable (1 pcs) Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Monoprice VoxelRobo E3 WARNING: Pay close attention to the...

  Flashforge Print Head Flat Cable This is the FPC flat cable that runs from the print head to the mainboard. Includes: FPC Cable (1 pcs) Fits:Adventurer 3Adventurer 3 Pro (not Pro 2)Monoprice VoxelRobo E3  WARNING Pay...

  Flashforge TFT Touch Screen Cable Runs from touch screen to mainboard Includes: FPC Cable (1 pcs) Fits:Adventurer 3Adventurer 3 ProMonoprice VoxelRobo E3D  WARNING Pay attention to the orientation of your current cable...

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

  Flashforge Front Door Includes: Front door (1 pcs)Magnets (2 pcs) Fits: Adventurer 3 (all models)Monoprice VoxelRobo E3

Replacement Fuse 5 amp fuse

  Flashforge 8a Fuse Includes: Fuse (2 pcs) Location: Power inlet plug (on/off switch) Fits: Adventurer 3 (all versions)Monoprice VoxelRobo E3

  Flashforge Glass Build Plate Assembly You can use this assembly to convert your Adventurer 3 to a glass build plate. Includes: Glass build plate (1 pcs)Build plate frame (1 pcs)Heater (1 pcs)Heater pads (4 pcs)Mounting screws (3 pcs)Bearing...

Flashforge 3D Printer Grease This is the same grease that comes standard with many Flashforge 3D Printers. Size: 3 Grams Includes: Grease packet (1 pcs)

  Flashforge Hotend Assembly (Print Head) Fully assembled.  Includes:0.40mm Nozzle assembly (1pcs)Fan (1 pcs)LED light (1 pcs)Internal PCB boards and wires Fits:Adventurer 3Adventurer 3 ProMonoprice VoxelRobo E3

  Flashforge Hotend (Print Head) Housing Includes:Top housing (1 pcs)Bottom housing (1 pcs)M3 screw (1 pcs) Fits: Adventurer 3Adventurer 3 ProMonoprice VoxelRobo E3 Note: Does not include: Nozzle, fan shroud or any...

Leadscrew Bushing This small plastic bushing is located at the bottom of the Z axis leadscrew. Includes: Bushing (1 pcs) Fits:Adventurer 3Adventurer 3 ProRobo E3Monoprice Voxel

  Flashforge LED Board Fits in the print head and lights the object being printed. Includes: LED Board (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versionsFinder 2Monoprice VoxelRobo E3

  Flashforge Build Plate Limit Switch (Y Axis Sensor) For the Y Axis Includes: Limit switch (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Monoprice VoxelRobo E3 Scroll down for Adventurer 4 instruction video 

  Flashforge Z Limit Switch This is the limit switch (endstop) for the Z axis. It is sometimes called the Z axis sensor switch. Includes: Limit switch (1 pcs) Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Monoprice VoxelRobo E3

M2x6mm Blunt Nose Screw Set Includes: Screws (5 pcs) Head: PanSize: M2Length: 6mmType: Blunt nose

  Timing Belt (Motor) Drive Pulley This is the drive pulley that is used on many Flashforge 3D printers. Includes:Pulley (1pcs)Pulley disc (1 pcs)E-clip (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Creator ProCreator Pro...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)