MK3S

Raspberry Pi Zero 2W for PrusaLink This is the Zero 2W version which is more powerful than the standard Zero W version.  Add PrusaLink functionality to your printer and/or add your printer to Prusa Connect. The Raspberry Pi Zero 2 W allows...

  Raspberry Pi Zero W for PrusaLink Add PrusaLink functionality to your printer and/or add your printer to Prusa Connect. The Raspberry Pi Zero W allows you to remotely control your 3D printer and attach additional peripherals like cameras...

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench (1 pcs) For:E3D V6Prusa i3RepRap

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...

Revo Coldside Only - For Prusa MK2 and MK3 Series  Notes:  This is not a complete upgrade kit, this is the coldside only.You will also need to purchase a hotside pack if you do not already have one (see links below). Includes:1 x Revo Six...

Revo™ HeaterCore (With 104NT Thermistor) Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring...

Revo High Flow, High Temp Abrasive (HF HT-A) Nozzle HF HT-A nozzles are high-temperature, high flow, abrasion-resistant nozzles. Much like ObXidian, these nozzles have a hardened steel tip, copper carrier and copper spreader segment to optimise the...

Revo Starter Pack - 24 Volt  Note 1:  Please take care when making your product selection.The 104NT (E3D) comes with an E3D 104NT thermistor.The 100K (Creality) comes with a Creality specific HeaterCore and is not compatible with other...

Revo High Flow or High Flow X Hotside Pack - 24 Volt, 60 Watt  Note:  These hotsides come with an integrated E3D 104NT thermistor. Make sure this is the correct thermistor for your printer before ordering. This is not a...

Revo™ ObXidian Nozzles The Revo ObXidian is specifically designed for printing fibre-filled polymers. ObXidian’s copper alloy construction has a similar thermal performance to Brass, making it a true drop-in replacement. Just use the...

Heatsink for Revo™ Six Includes:Heatsink (1 pcs)Collet (1 pcs)Collet clip (1 pcs)

Revo™ Silicone Sock Pack Includes:Yellow (2 pcs)Red (2 pcs)Blue (2 pcs)Green (2pcs)HeaterCore socks (2pcs) Fits: E3D Revo Nozzles and HeaterCore

Revo™ Spring Triple Pack Includes: Revo spring (3 pcs) These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo...

Screwdriver PH2 Screwdriver with a PH2 head. PH2 is the recommended standard for the screws used on Original Prusa Printers. Includes: Screwdriver (1 pcs) Specifications:Red Hand: PlasticScrewdriver length L1: 160 mmShank length...

Prusa MMU2S-Einsy/Rambo signal cable Replacement MMU2S-Einsy/Rambo signal cable Includes: Cable (1 pcs) Fits the following printers with MMU2S:MK2.5SMK3MK3S To replace this parts, please consult the Prusa Assembly Manuals. Make sure to follow...

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...

Sock-X for E3D Revo Nozzle Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. Designed specifically for the E3D Revo Nozzle...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. The primary purpose of a silicone sock is to help...