MK3S+

9mm SAC-1 Stainless-Steel Graphics Knife with 30-Degree Precision Blade High-quality precisely made stainless steel precision knife with an acute 30° snap angle for enhanced cutting control. Each blade offers seven cutting segments per blade...

Replacement Blades for the Olfa SAC-1 Precision Knife  High-quality precisely made stainless steel 9 mm blades with an acute 30° snap angle for enhanced cutting control. Each blade offers seven cutting segments per blade...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

Double-Sided textured PEI powder-coated spring steel sheet These sheets have MK3 printed on them, but will fit all the below listed printers.  Powder coating directly on metal makes it very hard to damage this build plate. If a heated nozzle...

Double-sided Satin PEI Powder-coated Spring Steel Sheet for the Original Prusa i3 Series Includes: Satin spring steel sheet (1 pcs) Prusa's satin sheet sits between the smooth and textured variants. Its powder-coated surface with...

Double-Sided textured PEI powder-coated spring steel sheet Powder coating directly on metal makes it very hard to damage this build plate. If a heated nozzle crashed into it, the metal can dissipate the heat. Powder coating also gives the surface a...

Double-sided Powder-coated PA Nylon Spring Steel Sheet Includes: Spring steel sheet (1 pcs) This print sheet is specially designed to print polyamide-based filaments, especially the Prusament PA11 Carbon Fiber Black. The PA11-type...

Double-sided Powder-coated PP Spring Steel Sheet Includes: Spring steel sheet (1 pcs) This print sheet is specially designed to print polypropylene-based filaments, especially the Prusament PP Carbon Fiber Black. The PP-type...

Original Prusa Spring Steel Sheet with Smooth Double-sided PEI This is the replacement spring steel sheet with smooth double-sided PEI for the Original Prusa i3 magnetic heatbeds. Perfect for PLAGreat adhesion with almost all materialsSmooth bottom...

Prusa PEI-Ultem sheet Notes: 1. This is NOT the Spring steel sheet with smooth double-sided PEI.2. Tiny dots may appear on the PEI-Ultem surface. These can slightly affect the finished print bottom surface. However, they do not...

PEI Print Surface - 260x242mm - for Prusa and other printers Includes: PEI sheet with 3M adhesive backing (1 pcs) Notes:1. This is NOT the Prusa spring steel sheet with smooth double-sided PEI (Link).2. Tiny dots may appear on the PEI...

Prusa MMU2S-Einsy power cable Replacement MMU2S to Einsy power cable.  Includes: Cable (1 pcs) Fits:MK3 with MMU2SMK3S with MMU2SMK3S+ with MMU2S Note: Only compatible with the MK3/S/+. NOT compatible with MK2.5/S printers...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

  Prusa Brass Nozzle Brush Prusa Brass Nozzle Brush is optimized for 3D printing with its short and dense bristles. Note: Please expect the bristles to bend during shipping, storage and usage; this is typical for brass brushes...

Prusa PSU - 24 Volts This is the replacement power supply unit ONLY. It does NOT come with any cables. Buy the MK3 PSU kit here.  Includes: Power supply unit (1 pcs) Specifications:Voltage: 24VDCWattage: 240WCurrent (MAX): 10AFuse:...

Prusa MK3 Power Supply Assembly Replacement Power supply unit 24V 240W (assembly). It is ONLY compatible with MK3/S/+. The PSU itself is also available separately, without any cables or fasteners. Includes:Power supply unit 24V...

PSU Cable Quick-release for Original Prusa Enclosure A quick-release connector for the 3D printer PSU cables. This is an ideal solution for everyone who often takes the printer out of the enclosure. This spare part is compatible only with the Original...

PB Select™ Prusa PSU Holder Nut - 2 Pack Nickel plated M3nE nut. Used to secure the PSU to the t-slot rail. Includes: M3nE Nut (2 pcs) Fits:Prusa MK2.5Prusa MK2.5SPrusa MK3Prusa MK3SPrusa MK3S+Prusa MINIPrusa MINI+ To replace this part, please...

Prusa Hotend PTFE Tube This is a replacement hotend PTFE tube. Includes: Hotend PTFE tube (1 pcs) Specifications:Length: 42.3 mm (tolerance +/- 0.2 mm)Inner diameter: 1.85 mmOuter diameter: 4 mm Fits:MK3S+MK3S+ with MMU2SMK3S+ with...

E3D 4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth. These are the small collets that fit E3D V6 and Prusa heatsinks. Includes: Collet (1 pcs)  Size:ID: 4mmOD: 5mm Fits: Bondtech ExtrudersE3D V6...