PB Select™

PB Select™ Y Carriage  Fits: Prusa MINIPrusa MINI+ Note: No hardware included.

Fan Shroud (Air Duct) MJF printed in nylon (PA12) for durability and temperature resistance.  Includes:Fan Shroud (1 pcs)Support Bracket (1 pcs) Fits: Prusa MK3S+...

PB Select™ Parakeet Bed Clips for MakerGear 3D Printers We designed these low profile bed clips for use with our MakerGear printers The clips have a small beak that just reaches the...

Screws for Creator Pro hotend assembly A selection of screws for the hotend assembly. Includes: M3x6 socket head cap screw (4 pcs)Wire support bracket to cold block M3x8 socket head cap...

Kapton and Aluminum Tape Used to attach the thermistor to the heated bed on Prusa 3D printers. Includes:Kapton Tape - adhesive backed, approximately 3X3 inches (1...

PB Select™ Kapton & Aluminum Tape Used to attach the thermistor to the heated bed on Prusa and other 3D printers. Includes:Kapton Tape...

CopperBlock™ Hot Block for Prusa MINI Nickel composite coated copper hot block for increased thermal conductivity.  Includes:Copper heater block (1 pcs)Set screw (1 pcs)Heater clamping...

Standard FEP Tube - Clear Sold by the meter: For example, if you order a qty of 4 you will get one 4 meter piece. Inside Diameter: 2mm (± .1mm) Outside Diameter:...

Premium PTFE Tube - Orange Sold by the meter: For example, if you order a qty of 4 you will get one 4 meter piece. Inside diameter: 1.9mm Outside...

PB Select™ 3mm Nylon Filament  This 3mm nylon filament is used in the wiring harness of Prusa i3 printers.The length is 50cm which is the proper length for the extruder...

Socket Adapter for Slice Engineering Torque Wrench This adapter allows for the use of 1/4 inch sockets with the Slice Engineering Nozzle Torque Wrench. With this adapter you can use the...

PB Select™ Heat Bed Power Cable This is the cable that runs from the Mainboard to the heated bed on Prusa MK2 series Note: ONLY compatible with the heated beds with detachable power cable...

PB Select™ PSU to Einsy Power Cable We use premium pure copper wire, tin plated copper connectors and adhesive heat shrink for a good quality long lasting cable. Includes: Power cable (1...

PB Select™ Prusa V-Cable Adapter This Reduction cable is needed to install a Noctua or Sunon 3 wire fan. Fits:Prusa MK2.5 Prusa MK2.5S  

PB Select™ MK2.5 PINDA Reduction Cable Includes: Cable (1 pcs)

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench...

Hotend Screw Assortment  A selection of screws for the extruder assembly. Notes: This is a selection and not a complete replacement set.Color of screws may be different than shown...

PB select™ Ball & Magnets for Prusa Filament Runout Sensor Includes:19x6x2mm magnet (1 pcs)10x6x2mm magnet (2 pcs)7mm steel ball (1 pcs)

Heater Cartridge - 12v 40w This premium heater cartridge provides consistent heating throughout the cartridge for better heat distribution to the heater block. Includes: Heater (1 pcs) Use BN...

PB Select™ Thermistor for Prusa Heated Bed Includes: Bed thermistor (1 pcs) Cable length: 630 mm Fits:MINIMINI+MK2MK2SMK2.5MK2.5SMK3MK3SMK3S+ Note: Does not include the...