MINI/+

PTFE Fittings Set for Prusa Mini Use this set to simplify the install, use and maintenance of Prusa Mini’s bowden tube.Instead of using 3 PTFE tube sections, use one only.Includes push-fit collets for ease of use and effective hold of the...

Prusa MINI PTFE Tube - Extruder to Print head  Runs from the extruder to the print head. Includes:Extruder-Print head PTFE tube (1 pcs) Swivel nut (2 pcs)Pressed olive part (2 pcs) Specifications:Length: 275 mmInner diameter: 2 mmOuter...

Pre-Extruder PTFE Tube This PTFE tube runs from the extruder to filament spool. Included: PTFE tube (1 pcs) Specifications:Length: 150 mmInner diameter: 2 mmOuter diameter: 4 mm Fits:MINIMINI+ To replace this part, please consult the Prusa Assembly...

  Prusa MINI Hotend PTFE Tube This is the hotend PTFE tube. Includes: PTFE tube (1 pcs) Specifications:Length: 43.4 mmInner diameter: 2 mmOuter diameter: 4 mm Fits:MINIMINI+ Note: This is ONLY compatible with the Original Prusa MINI and...

PC4-M8 Push Fit Connector For use with Capricorn or similar PTFE tubing. Includes: Push Fit Connector (1 pcs) Fits:Prusa MINIPrusa MINI+ Notes:The internal depth of this fitting is not as deep as the stock fitting, so you may need to...

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...

Revo Coldside Only - For Prusa MINI/+  Notes:  This is not a complete upgrade kit, this is the coldside only.You will also need to purchase a hotside pack if you do not already have one (see links below). Includes:Collet (1 pcs)Collet...

Revo™ HeaterCore (With 104NT Thermistor) Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring...

Revo High Flow, High Temp Abrasive (HF HT-A) Nozzle HF HT-A nozzles are high-temperature, high flow, abrasion-resistant nozzles. Much like ObXidian, these nozzles have a hardened steel tip, copper carrier and copper spreader segment to optimise the...

Revo High Flow or High Flow X Hotside Pack - 24 Volt, 60 Watt  Note:  These hotsides come with an integrated E3D 104NT thermistor. Make sure this is the correct thermistor for your printer before ordering. This is not a...

Revo™ ObXidian Nozzles The Revo ObXidian is specifically designed for printing fibre-filled polymers. ObXidian’s copper alloy construction has a similar thermal performance to Brass, making it a true drop-in replacement. Just use the...

Revo™ Silicone Sock Pack Includes:Yellow (2 pcs)Red (2 pcs)Blue (2 pcs)Green (2pcs)HeaterCore socks (2pcs) Fits: E3D Revo Nozzles and HeaterCore

Revo™ Spring Triple Pack Includes: Revo spring (3 pcs) These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo...

Screwdriver PH2 Screwdriver with a PH2 head. PH2 is the recommended standard for the screws used on Original Prusa Printers. Includes: Screwdriver (1 pcs) Specifications:Red Hand: PlasticScrewdriver length L1: 160 mmShank length...

Sock-X for E3D Revo Nozzle Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. Designed specifically for the E3D Revo Nozzle...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. The primary purpose of a silicone sock is to help...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...