Prusa

Heatsink for Revo™ Six Includes:Heatsink (1 pcs)Collet (1 pcs)Collet clip (1 pcs)

Revo™ Silicone Sock Pack Includes:Yellow (2 pcs)Red (2 pcs)Blue (2 pcs)Green (2pcs)HeaterCore socks (2pcs) Fits: E3D Revo Nozzles and HeaterCore

Revo™ Spring Triple Pack Includes: Revo spring (3 pcs) These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo...

Prusa XL Rubber Foot Includes: Rubber foot (1 pcs) Fits: XL

PB Select™ Nextruder Hotend Screw Kit Includes:Set Screw (5 pcs)Pan Head Screw (2 pcs)T6 Torx WrenchT8 Torx Wrench Specs:Set Screw: M3x5mm, T6 torx headFor fastening thermistors and heater cartridge Pan Head: M2.5x6mm, T8 torx headFor fastening...

Screwdriver PH2 Screwdriver with a PH2 head. PH2 is the recommended standard for the screws used on Original Prusa Printers. Includes: Screwdriver (1 pcs) Specifications:Red Hand: PlasticScrewdriver length L1: 160 mmShank length...

Selector Motor for MMU2S/MMU3 Includes:Selector motor (1 pcs)Trapezoid nut (1 pcs) Specifications:Connector: MOLEX 50-57-9404Rated current: DC 1A Fits:MMU2SMMU3 To replace this part, please consult the Prusa Assembly Manuals. Make sure to...

M3x4 Set Screw (Grub Screw) Includes: Set screw (5 pcs) Size: M3x4mmGrade: 12.9Head Type: Hex Fits heater block of:E3D V6Prusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4SPrusa XL Note: These are hex head set screws, not torx head (torx head is...

M3X4 Torx Head Set Screw Used on the Nextruder heater block Includes: M3x4 set screw (5 pcs) Note: Uses T6 Torx driver to install (not included) Fits:Prusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4SPrusa XL

Prusa MMU2S-Einsy/Rambo signal cable Replacement MMU2S-Einsy/Rambo signal cable Includes: Cable (1 pcs) Fits the following printers with MMU2S:MK2.5SMK3MK3S To replace this parts, please consult the Prusa Assembly Manuals. Make sure to follow...

PB Select™ Silicone Sock Includes: Silicone sock (2 pcs) Color: BlackMax temperature: 280°c Fits:Prusa CORE OnePrusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4SPrusa XL

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...

Sock-X for E3D Revo Nozzle Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. Designed specifically for the E3D Revo Nozzle...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. The primary purpose of a silicone sock is to help...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. The primary purpose of a silicone sock is to help...

Sock-X This premium silicone sock can handle printing temps of up to 300c. Designed specifically for the Prusa MINI and MINI+ hotends.  The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing...