Robo 3D

  Flexible Build Plate with Smooth PEI Smooth PEI printing surface on one side. Includes: Flexible build plate (1 pcs)PEI print surface - pre-installed (1 pcs) Fits:AD5XAdventurer 5MAdventurer 5M ProRobo E4

  Textured PEI Flexible Build Plate  Powder coated textured PEI print surface on both sides. More durable than the smooth PEI print surface. Includes: Build plate (1 pcs) Fits:AD5XAdventurer 5MAdventurer 5M ProRobo E4 

  Flashforge Flexible Build Plate Includes:Flexible steel sheet (1 pcs)Print surface (1 pcs) Fits: Guider 3Robo E4 Pro

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

  Flashforge Front Door Includes: Front door (1 pcs)Magnets (2 pcs) Fits: Adventurer 3 (all models)Monoprice VoxelRobo E3

  Acrylic Front Door for ADV 5M Pro Includes: Front door (1 pcs)Magnets - installed (2 pcs) Fits: Adventurer 5M ProRobo E4

Replacement Fuse 5 amp fuse

  Flashforge 8a Fuse Includes: Fuse (2 pcs) Location: Power inlet plug (on/off switch) Fits: Adventurer 3 (all versions)Monoprice VoxelRobo E3

  Flashforge FFC Flat Cable for Bed Gauge Sensor Runs from heated build plate to strain gauge sensor board. Includes: FFC Cable (1 pcs) Fits:Adventurer 5MAdventurer 5M ProRobo E4 Note: This is narrow cable that plugs into the bed, not...

  Flashforge Glass Build Plate Assembly You can use this assembly to convert your Adventurer 3 to a glass build plate. Includes: Glass build plate (1 pcs)Build plate frame (1 pcs)Heater (1 pcs)Heater pads (4 pcs)Mounting screws (3 pcs)Bearing...

Flashforge 3D Printer Grease This is the same grease that comes standard with many Flashforge 3D Printers. Size: 3 Grams Includes: Grease packet (1 pcs)

Robo C2 Belt This is the short belt that runs from the stepper motor to the X/Y axis shaft. Includes: Belt (1 pcs) Length: 260mm Fits: Robo C2

PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm

PB Select™ GT2 Pulley - 2 Pack Includes:Pulley (2 pcs) Set Screws (4 pcs) Fits: 8mm Linear Rods Specs:20 Tooth7mm Wide (for 6mm belt)8mm Bore  

PB Select™ GT2 Drive Pulley  Recommended for use with Gates GT2/3 belts Includes:Pulley (1 pcs)Set screw (2 pcs) Fits: 8mm Shaft Specs:20 Tooth7mm Wide (for 6mm belt)8mm Bore

GT Belt for Robo C2  Includes: Closed Loop Belt (1 pcs) Size: 6x466mm Fits: Robo C2 X or Y Axis

Flashforge Hardened Steel Nozzle Hardened steel nozzles for printing with abrasive materials  Includes: Nozzle of selected size (1 pcs) Material: Hardened Steel Fits:Guider 3Guider 3 PlusCreator 3 Pro (does not fit standard Creator...

  Flashforge Hardened Steel Nozzle Set This upgraded nozzle set is more abrasion resistant for printing carbon fiber filled and other abrasive filaments. Includes:0.40mm (2 pcs)0.60mm (2 pcs)0.80mm (2 pcs) Fits: Guider 3Guider 3 PlusCreator...

HDMI Cable Board-to-LCD connection cable Includes: Cable (1 pcs)  Fits: Robo R2Robo C2    

  Flashforge Heat Break (Threaded Pipe)  Includes: Heat break (1 pcs) Fits: Guider 2S HTRobo E3 Pro