Robo 3D

  Flashforge Power Supply Includes: Power supply (1 pcs) Fits:Adventurer 3Adventurer 3 Pro (not Pro 2)Monoprice VoxelRobo E3

  Flashforge Replacement Power Supply (PSU) Includes: Power supply (1 pcs) Fits: Creator 3Guider 2Guider 2S HTRobo E3 Pro

Power Supply for Robo R1+ 3D Printer Includes: Power supply (1 pcs) Specifications:Volts: 12 VDCWatts: 400 Fits: Robo R1Robo R1+

Power Supply Includes:Power supply unit (1 pcs)Cable (1 pcs) Voltage: 19 VDC Fits: Robo C2

  Power Supply Unit (PSU) Includes: PSU (1 pcs) Fits:Adventurer 5MAdventurer 5M ProRobo E4

Power Rocker Switch for Robo R1+ 3D Printer Includes: Switch (1 pcs) Fits: Robo R1Robo R1+

Print Bed Plastic Housing for Robo R2 Includes: Plastic bed housing (1 pcs) Notes: This is the plastic housing only.Does not include screws: Reuse the screws from your old bed. Does not include magnets: Reuse the magnets...

  Flashforge X Carriage (Print Head Mounting Bracket) This is the bracket the print head mounts to and slides back and forth on the X carriage.  Includes: Bracket (1 pcs) Fits: Adventurer 3Adventurer 3 ProRobo E3Monoprice Voxel Note:...

Robo Print Surface (Bed Tape) Adhesive backed for easy installation Includes: Print surface sheet (1 pcs) Size: 235x235mm Fits:  Robo E4

  Flashforge Print Surface (Bed Tape) Adhesive backed for easy application Includes: Print Surface (1 pcs) Size: 263x307mm (can be trimmed to fit other printers) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Print Surface (Bed Tape) Adhesive backed for easy installation Includes: Print surface sheet (1 pcs) Fits: Guider 3Robo E4 Pro 

  Flashforge PTFE Tube Runs from the filament feeder (extruder) to the print head. Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Monoprice VoxelRobo E3 Note: Does not include snap ring Watch the videos below for helpful information on...

  Flashforge Hotend/Nozzle PTFE Tube This the PTFE tube that goes inside the heatsink.  Includes: PTFE tube for hotend (1 pcs) Length: 26.75mm Fits: Guider 2S HTRobo E3 Pro

  Flashforge Idler (Driven) Pulley Assembly Includes:Pulley (1 pcs)29mm shaft (1 pcs)10mm Flange Bearing (2 pcs)E-clip (2 pcs) Location: X axis Fits:Guider 2Guider 2S HTRobo E3 Pro Note: This pulley uses 10mm flange bearings and will...

  Flashforge Idler (Driven) Pulley Assembly Includes:Pulley (1 pcs)35mm shaft (1 pcs)Spacer (1 pcs)10mm Flange Bearing (2 pcs)E-clip (2 pcs) Location: Y-Axis Fits:Guider 2Guider 2S HT Note: These pulleys use 10mm flange bearings and...

  Flashforge Y Axis Drive Pulley Assembly This is the drive pulley with coupler for the newer style stepper motor/shaft. This uses a coupler (included) to connect the drive shaft to the pulley assembly. Includes: Pulley Assembly (1...

  Brass Push Fit Connector (latest version) This is the latest version of the push fit connector from Flashforge. It replaces the older silver push fit connector (see picture below).  Includes: Push fit connector (1...

Standoffs for Mounting Raspberry Pi Includes: Standoff (4 pcs) Fits:Robo R2Robo C2

Ribbon Cable - Uptown to Downtown Board  Includes: Cable (1 pcs) Fits:Robo R2Robo C2

  Microswiss Wear-Resistant Nozzle with M6 Threads This M6 thread, Robo 3D style nozzle is made from a 360 brass base material and plated with TwinClad XT coating. TwinClad XT is a nickel composite coating designed for very low friction. It offers...